User manual TOSHIBA RAS-16GAVP-E PSD

[. . . ] CONSTRUCTION VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS OF ELECTRICAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT CYCLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Comfort sleep Indicates when comfort sleep is activaled. Press comfort sleep button to selectter 11. Quiet Indicates when quiet is activated. Press quiet button to start and press it again to stop operation. One-Touch Indicates when one touch comfort is activated. Press one-touch button to start the operation. Press swing button to start the swing operation and press it again to stop the swing operation. 11 8 6 3 7 4 5 ­ 46 ­ FILE NO. Installation Diagram of Indoor and Outdoor Units 65 mm or more 170 For the rear left and left piping Hook mm or m ore 1 Installation plate Wall Hoo k 170 mm or m ore Insert the cushion between the indoor unit and wall, and tilt the indoor unit for better operation. Do not allow the drain hose to get slack. A ir f ilt e r (A t t ac h to t he f ro n Shield pipe 5 t pa n el . ) Cut the piping hole sloped slightly . Super Oxi Deo filter 6 Super Sterilizer filter Make sure to run the drain hose sloped downward. 3 Batteries 8 Pan head wood screw 4 Remote control holder The auxiliary piping can be connected to the left, rear left, rear right, right, bottom right or bottom left. Right 2 Vinyl tape Apply after carrying out a draina ge test. Wireless remote 600 mm or more Rear right Bottom right Rear left Left Bottom left m 45 m o or m re Saddle Insulate the refrigerant pipes separately with insulation, not together. 10 0 mm or m o re 400 m r mo re mo Extension drain hose (Not available, provided by installer) 6 mm thic k heat resisting pol yethylene f oam 600 mm or m o re Before installing the wireless remote controller · Loading Batteries 1. Insert 2 new batteries (AAA type) following the (+) and (- ) positions. A C L 3 Batteries 2 Wireless remote controller - 47 - FILE NO. · Also, the "charge port and packing for refrigerant cylinder" require 1/2 UNF 20 threads per inch corresponding to the charge hose's port size. ­ 50 ­ FILE NO. Cutting a hole and mounting installation plate 42 mm <Cutting a hole> · A place which provides the spaces around the When installing the refrigerant pipes from the rear. indoor unit as shown in the above diagram. · A place where there is no obstacle near the air inlet and outlet. 90 mm · A place that allows easy installation of the piping to 66 mm the outdoor unit. · A place which allows the front panel to be opened. · The indoor unit shall be installed as top of the indoor unit comes to at least 2 m height. Also it must be avoided to put anything on the top of Pipe hole the indoor unit. 65 mm CAUTION · Direct sunlight to the indoor unit's wireless receiver should be avoided. · The microprocessor in the indoor unit should not be too close to RF noise sources. (For details, see the owner's manual. ) <Remote controller> · A place where there are no obstacles such as a curtain that may block the signal from the indoor unit. · Do not install the remote control in a place exposed to direct sunlight or close to a heating source, such as a stove. [. . . ] Detachment 1) Perform work of item 1 of 1 and 1 of 2. Requirement: Perform the work on a corrugated cardboard, cloth, etc. 2) Remove the front cabinet, and place it down so that the fan guard side faces downwards. 3) Remove the hooking claws by pushing a minus screwdriver according to the arrow mark in the right figure, and remove the fan guard. [. . . ]