User manual TOSHIBA RAS-18YAH-E SERVICE MANUAL

[. . . ] A00-0001 SUPPLEMENT SERVICE MANUAL AIR-CONDITIONER SPLIT WALL TYPE RAS-18YKH-E / RAS-18YAH-E RAS-18YKH-A / RAS-18YAH-A PRINTED IN THAILAND, Apr. , 2000 CONTENTS 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONSTRUCTION VIEWS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect BLUE colored core to plug terminal marked letter "N". Connect GREEN and YELLOW colored core to plug terminal marked Earth symbol " ". The installation of the cables has to be done in such a way that the basic insulated wires for the infrared sensor can not be touched. Use the power supply cord/cables with thickness, type, and protective devices specified in the installation manual. Prepare the interior power supply cord and cables wiring with current capacity sufficient for starting and usage of air conditioner. CAUTION 1. Wrong wiring connection may cause some electrical parts burn out. Be sure to use the cord clamps and the electric parts cover to the specified positions with attached to the product. Mount the electrical parts cover for cables of connecting section firmly with the screws. Do not damage or scratch the conductive core and inner insulator of power supply and inter connecting cables when peeling them. Be sure to comply with local cords on running the wire from indoor unit to outdoor unit (size of wire and wiring method etc. ) Wire type : More than H05 RN-F 5. Use the power supply cord and inter-connecting cable with specified thickness, specified type, and protective devices specified. No wire should touch refrigerant piping, compressor of any moving parts. Fig. Insert a flare nut into the pipe, and flare the pipe. Outer dia. (mm) 6, 35 12, 7 A (mm) Thickness (mm) Imperial Rigid 1, 3 0, 7 0, 8 1, 8 1, 0 to 1, 1 1, 0 Packed Valve Handling Precautions Die Pipe Tightening Connection Fig. 8-4-3 Align the centers of the connecting pipes and tighten the flare nut as far as possible with your fingers Then tighten the nut with a spanner and torque wrench as shown in the figure. · Open the valve stem all the way out; so not try to open it beyond the stopper. · Securely tighten the valve stem cap torque is as follows; Gas pipes side (ø12, 7 mm) : 49 N·m (5, 0 kgf·m) Liquid pipe side (ø6, 35 mm) : 16 N·m (1, 6 kgf·m) Hexagon wrench is required. Flare nut Stopper Valve stem cap Fig. TROUBLESHOOTING CHART Troubleshooting Procedures : · Following details of "What to be pre-checked first", make sure of the basic items. · When there is no trouble corresponding to above, check in detail the faulty parts following "How to judge faulty parts by symptoms" later. 9-1-2. Incorrect Cable Connection between Indoor and Outdoor Units The indoor unit is connected to the outdoor unit with 4 cables. Make certain that the indoor and outdoor units have been connected properly, with terminals assigned the same numbers wired to each other. If the connectors are not connected as specified, the outdoor unit will not operate normally, or OPERATION lamp and TIMER lamp will flash (5Hz). 9-1. [. . . ] YES NO Does the transmission indicator light?YES NO Is there any beep and operation?YES Can any signal tone be heard in a transistor radio when transmitting within 5cm distance from the radio?Keep the air conditioner away from thyristor fluorescent light. Remote control is failure. Avoid direct sunlight. Replace P. C. [. . . ]