User manual TOSHIBA RAV-103NH-PE SERVICE MANUAL

[. . . ] AIR DUCTING WORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONSTRUCTION VIEWS (EXTERNAL VIEWS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SYSTEMATIC REFRIGERATING CYCLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After completion of setup, push button to return the status to the usual stop status. 1 minute is required to start handling of the remote controller. ) * 01 to 9F are provided in the item code (DN). When data has been changed by mistake and SET button has been pushed, the data can be returned to the data before change by pushing button if the item code (DN) was not yet changed. 6 <REMOTE CONTROLLER> 6 SET DATA UNIT No. R. C. No. 6 4 1 UNIT SET CL 3 5 ­ 90 ­ 2 Memorandum for setup contents (Item code table (Example)) DN 01 02 03 06 0F 10 11 12 13 14 19 1E 28 2A 2b 2E 32 5d 60 8b Item Filter sign lighting time Dirty state of filter Central control address Heating suction temp shift Cooling only Type Indoor unit capacity Line address Indoor unit address Group address Flap type (Adjustment of air direction) Temp difference of automatic cooling/ heating selecting control points Automatic reset of power failure Option Thermo output selection (T10 B) Option Sensor selection High ceiling selection Timer set (Wired remote controller) Correction of high heat feeling Memo At shipment According to type 0000: Standard 0099: Unfixed 0002: +2°C (Floor type: 0) 0000: Shared for cooling/heating According to model type According to capacity type 0099: Unfixed 0099: Unfixed 0099: Unfixed According to type 0003: 3 deg (Ts ± 1. 5) 0000: None 0002: 0000: Thermo ON 0000: 0000: Body sensor 0000: Standard 0000: Available 0000: None Type Item code [10] Setup data 0001* 0004 Type 4-way air discharge cassette Concealed duct Abbreviated name RAV-SM560/800TU-E RAV-SM560/800BT-E * Initial setup value of EEPROM installed on the service P board . C. Indoor unit capacity Item code [11] Setup data 0000* 0009 0012 Model Invalid 56 80 * Initial setup value of EEPROM installed on the service P board . C. ­ 91 ­ 12. Test Run Setup on Remote Controller <Wired remote controller> 1. When pushing button on the remote controller for 4 seconds or more, "TEST" is displayed on LC display. Then push · "TEST" is displayed on LC display during operation of Test Run. · During Test Run, temperature cannot be adjusted but air volume can be selected. · In heating and cooling operation, a command to fix the Test Run frequency is output. · Detection of error is performed as usual. However, do not use this function except case of Test Run because it applies load on the unit. (OK if display goes on. ) · To change the selected indoor unit, proceed to · To change the item to be set, proceed to 3. 2. 6 Pushing button returns the status to usual stop status. SET DATA UNIT No. R. C. No. 6 4 1 UNIT SET CL 3 5 <Operation procedure> 2 4 5 6 END 1 2 3 ­ 93 ­ Item No. (DN) table (Selection of function) DN 01 Item Filter sign lighting time 0000 : None 0002 : 2500H 0004 : 10000H 0000 : Standard Description 0001 : 150H 0003 : 5000H 0005 : Clogged sensor used 0001 : High degree of dirt (Half of standard time) to 0064 : No. 64 unit At shipment According to type 02 Dirty state of filter 0000 : Standard 03 Central control address 0001 : No. 1 unit 0099 : Unfixed 0099 : Unfixed 06 Heating suction temp 0000 : No shift shift 0002 : +2°C to 0001 : +1°C 0010 : -10°C (Up to recommendation + 6) 0001 : Cooling only (No display of [AUTO] [HEAT]) 0002 : +2°C (Floor type 0000: 0°C) 0F Cooling only 0000 : Heat pump 0000 : Shared for cooling/ heating According to model type According to capacity type 0099 : Unfixed 0099 : Unfixed 0099 : Unfixed 10 11 12 13 14 Type Indoor unit capacity Line address Indoor unit address Group address 0000 : (Air discharge cassette 1) 0001 : (Air discharge cassette 4) to 0037 0000 : Unfixed 0001 : No. 1 unit 0001 : No. 1 unit 0000 : Individual 0002 : Sub of group 0000 : No flap 0004 : 4-way to to 0001 to 0034 0030 : No. 30 unit 0064 : No. 64 unit 0001 : Master of group 19 Flap type (Adjustment of air direction) 0001 : Swing only According to type 1E Temp difference of 0000 : 0 deg to 0010 : 10 deg automatic cooling/ (For setup temperature, reversal of COOL/HEAT by ± (Data value)/2) heating mode selection COOL HEAT, HEAT COOL Automatic reset of power failure Option Thermo output selection (T10 ) Option Option Option Sensor selection Option High ceiling selection 0000 : Standard filter (Air volume selection) 0001 : Oil guard, Super-long life, Optical regenerative deodorization 0003 : High performance (65%), High performance (90%), High antibacterial performance (65%) Timer set (Wired remote controller) Correction of high heat feeling 0000 : Available (Operable) 0001 : Unavailable (Operation prohibited) 0000 : Body TA sensor 0001 : Remote controller sensor 0000 : Indoor thermo ON 0001 : Output of outdoor comp-ON receiving 0000 : None 0001 : Reset 0003 : 3 deg (Ts±1. 5) 28 0000 : None 2A 2b 0002 : Default 0000: Thermo. ON 2E 30 31 32 40 5d 0000 : Default 0000 : Default 0000 : Default 0000 : Body sensor 0003 : Default 0000 : Standard 60 0000 : Available 8b 0000 : None 0001 : Correction 0000 : None ­ 94 ­ 12-1-3. Cabling and Setting of Remote Controller Control 2-remote controller control (Controlled by two remote controllers) One or multiple indoor units are controlled by two remote controllers. 2 remote controllers are connectable. ) · 1 indoor unit is controlled by 2 remote controllers Remote controller Remote controller switch (Sub) switch (Master) Sold separately Sold separately Remote controller cables (Procured locally) Terminal block for remote controller cables AB Indoor unit 123 123 Outdoor unit (Setup method) One or multiple indoor units are controlled by two remote controllers. 2 remote controllers are connectable. ) <Wired remote controller> How to set wired remote controller to sub remote controller Insert the remote controller address connector provided on the rear side of the remote controller switch P board into Sub in exchange for Master. . C. Rear side of remote controller P. C. board Remote controller address connector Master remote controller Sub remote controller <Wireless remote controller> How to set wireless remote controller to sub remote controller Change OFF of Bit [3: Remote controller Sub/ Master] of switch S003 to ON. Sensor cover Adjust corner cap S003 Bit 1 : OFF to ON ON Sensor P. C. board 4 3 2 1 [Operation] 1. The operation contents can be changed by Last-push-priority. [. . . ] exclusive breaker, the control P board of the inverter assembly may cause a failure. Cord heater installation work procedure No. 1 1-2 Photo / Explanatory diagram Procedure Remove each cabinet, inverter assembly, motor base assembly, and partition board assembly. * Do not damage the electric parts such as cables, connectors, etc. [. . . ]