User manual TOSHIBA RD-XV45

[. . . ] E439BBD_EN. book Page 2 Wednesday, May 31, 2006 4:01 PM Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Laser Safety This unit employs a laser. Only a qualified service personnel should remove the cover or attempt to service this unit, due to the possibility of eye injury. [. . . ] If you select "Yes", you can continue with the dubbing, and the Timer Recording will start after the dubbing ends. Be noted that with VCR to DVD dubbing, the unit recognise DVD's remaining time as the dubbing duration although the actual dubbing will end when the videotape ends. Preparing for dubbing: · Insert a videotape to be dubbed. Example: VCR HDD DUBBING Introduction Dubbing Direction Rec Mode HDD DVD VD HDD VCR DVD VD VCR DVD DVD HDD VCR HDD VCR DVD D XP SP LP EP SLP SEP Connections 4 Select a desired Rec Mode using [Cursor U / D], then press [ENTER]. Dubbing Top Menu will appear. DUBBING Basic Setup Dubbing List Direction VCR HDD Mode XP Recording Preparing for dubbing (VCR to HDD): · Make sure there is enough space on the HDD. Preparing for dubbing (VCR to DVD): · Insert a recordable DVD. (See pages 28 to 30. ) · Make sure there is enough space on the DVD. Press [VCR] first. Dubbing Start 5 With "Dubbing Start" selected, press [ENTER]. Confirmation window will appear. Start Dubbing?Yes No Playback 1 Press [PLAY P] to start playback of the videotape, and press [STOP S] when it reaches the point you want to start dubbing. Press [DUBBING MODE]. The Dubbing Direction and the Rec Mode Menu will appear. DUBBING 6 Select "Yes" using [Cursor L / P], then press [ENTER]. Dubbing will start. 2 Dubbing Direction Rec Mode HDD DVD VD HDD VCR DVD VD VCR DVD D HDD VCR HDD VCR DVD DVD High XP SP LP EP SLP SEP Auto To stop the dubbing while in the dubbing preparation mode: · Press the Device Select Button of the recording device first (for example, if you are dubbing to DVD, press [DVD] first), then press [STOP S]. To stop the dubbing in progress: · Press the Device Select Button of the recording device first (for example, if you are dubbing to DVD, press [DVD] first). Then press and hold [STOP S] for 2 seconds. Or press [STOP S] on the front panel. Editing Function Setup 3 Note For HDD dubbing: Select "VCR HDD" using [Cursor U / D], then press [ENTER]. For DVD dubbing: Select "VCR DVD" using [Cursor U / D], then press [ENTER]. · The device mode change is available only between HDD and DVD during the videotape to the HDD / DVD dubbing. · After starting dubbing, the picture may be distorted because of the digital tracking function. Be advised to playback the videotape until the picture is stabilized, then set the starting point at which you wish to start recording, and start dubbing. · Playback audio is determined by the setting you make in the "Selecting the Sound Mode" section on page 91. VCR Functions Others EN 47 E439BBD_EN. book Page 48 Wednesday, May 31, 2006 4:01 PM Settings for external equipment Connection to external equipment VR Video Dubbing from the external devices VR Video HDD VCR DVD-RW DVD-RW DVD-R HDD VCR DVD-RW DVD-RW DVD-R Connect the external equipment using either the input jacks, AV1(TV) (Rear), AV2(DECODER) (Rear) or AV3 (Front). However, for AV3 jacks, you have to select S-VIDEO input or VIDEO input jacks depending on the connected devices. Use a commercially available Scart, S-Video or Video cable and an Audio cable for this connection. Before recording from an external device, connect the external device correctly by following the direction on the left, and turn the power of the unit and the external device on. 1 2 Turn on the TV. Select the appropriate external input channel. (See pages 22 to 23. ) 1 2 3 4 Press [SETUP]. "Easy Setting Menu" or "Advanced Menu" will appear. If "Advanced Menu" is displayed, proceed to step 3. Select the recording media. Recording to DVD: Press [DVD] first and insert a disc. · It may take awhile to load the disc. Select "Advanced Menu" using [Cursor U / D], then press [ENTER]. Select "Initial Setup" using [Cursor U / D], then press [ENTER]. Select "Display" using [Cursor U / D], then press [ENTER]. Display Menu will appear. Display Select Video FL Dimmer Screen Saver 3 Recording to a videotape: Press [VCR] and insert a videotape. [. . . ] Both formats were developed by Digital Theater Systems, Inc. Finalise To make DVDs that have been recorded playable in DVD players, finalise DVD-RW / R discs with this unit. JPEG (Joint Photographic Experts Group) JPEG is a method of compressing still image files. You can copy JPEG files on CD-RW / R discs from a computer and play back the files on this unit. [. . . ]