User manual TOSHIBA SATELLITE PRO 6070

[. . . ] AMD, AthlonTM, AthlonTM XP, ThoroughbredTM, and DuronTM are registered trademarks of AMD Corporation. Intel® and Pentium® are registered trademarks of Intel Corporation. PS/2 and OS ® /2 are registered trademarks of International Business Machines Corporation. W indows ® 95/98/2000/NT/XP are registered trademarks of Microsoft Corporation. [. . . ] Due to the IDE1 & SATA7 is controlled by Marvell 88SE6111, the BIOS will not detect the IDE & SATA device and will not show the status. 3-7 M S-7357 M ainboard Floppy Drive A This item allows you to set the type of floppy drives installed. Available options: [None], [360K, 5. 25 in. ], [1. 2M, 5. 25 in. ], [720K, 3. 5 in. ], [1. 44M, 3. 5 in. ], [2. 88M, 3. 5 in. ]. System Information Press <Enter> to enter the sub-menu, and the following screen appears: This sub-menu shows the CPU information, BIOS version and memory status of your system (read only). 3-8 BIOS Setup Advanced BIOS Features Boot Sector Protection This function protects the BIOS from accidental corruption by unauthorized users or computer viruses. W hen enabled, the BIOS' data cannot be changed when attempting to update the BIOS with a Flash utility. To successfully update the BIOS, you'll need to disable this Flash BIOS Protection function. You should enable this function at all times. The only time when you need to disable it is when you want to update the BIOS. After updating the BIOS, you should immediately re-enable it to protect it against viruses. Full Screen Logo Display This item enables you to show the company logo on the bootup screen. Settings are: [Enabled] Shows a still image (logo) on the full screen at boot. [Disabled] Shows the POST messages at boot. if the system fails to boot from the 1st/ 2nd/ 3rd boot device. 3-11 M S-7357 M ainboard Integrated Peripherals USB Controller This setting allows you to enable/disable the onboard USB controller. USB Device Legacy Support Select [Enabled] if you need to use a USB-interfaced device in the operating system. Onboard LAN Controller This item is used to enable/disable the onboard LAN controller. LAN Option ROM This item is used to decide whether to invoke the Boot ROM of the LAN controller. Onboard IEEE1394 Controller This item allows you to enable/disable the onboard IEEE1394 controller. Extra IDE Controller This setting is used to enable/disable the onboard IDE controller. HD Audio Controller This setting is used to enable/disable the onboard audio controller. 3-12 BIOS Setup On-Chip ATA Devices Press <Enter> to enter the sub-menu and the following screen appears: PCI IDE BusMaster Set this option to [Enabled] to specify that the IDE controller on the PCI local bus has bus mastering capability. RAID Mode (for ICH9R only) The SATA RAID Mode supports RAID0, 1, 5, 10. If AHCI is chosen, it allows you to enable SATA Stagger Spinup Support(not RAID mode) and take all hard disks on board as master. I/O Devices Press <Enter> to enter the sub-menu and the following screen appears: COM Port 1 This item specifies the base I/O port addresses of the onboard Serial Port 1 (COM 1). Selecting [Auto] allows AMIBIOS to automatically determine the correct base I/O port address. 3-13 M S-7357 M ainboard Power Management Setup Important S3-related functions described in this section are available only when your BIOS supports S3 sleep mode. [. . . ] Please select the device you have plugged in. - If the device is being plugged into the correct jack, you will be able to find the icon beside the jack changed to the one that is same as your device. - If not correct, Realtek HD Audio Manager will guide you to plug the device into the correct jack. B-12 Realtek ALC888 Audio Connector Settings Click to access connector settings. Disable front panel jack detection (option) Jack detection function only works with HD audio front panel. M ute rear panel output when front headphone plugged in. [. . . ]