User manual TOSHIBA SATELLITE 1710CDS FIELD REPLACEABLE UNIT DOCUMENTATION

[. . . ] Pressing the Enter key again will select the highlighted choice. n Device control feature parameters, such as changing I/O addresses and boot devices. System Data Security feature parameters, such as passwords. Entering the BIOS Setup Utility To enter the BIOS Setup Utility do the following: 1. Press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed. [. . . ] When selected, opens the Keyboard/Mouse Features submenu, which enables and disables the power-on state for [Numlock]. When selected, opens the Video Features submenu, which allows setting of the display parameters, including routing of video signals to different displays. When selected, opens the Internal Device Configuration submenu, which allows enabling or disabling the IDE Controller. When selected, opens the CPU Features submenu, which allows enabling or disabling the SpeedStepTM Technology feature for optimal battery life. When selected, opens the USB Features submenu, which allows enabling or disabling of Legacy Floppy Emulation. When selected, opens the Miscellaneous Configurations submenu, which allows you to configure the power button. When selected, opens the event logging submenu. Internal Device Configurations CPU Features USB Features Miscellaneous Configurations Event Logging 12 Advanced Menu Serial/Parallel Port Configuration Submenu of the Advanced Menu The Serial/Parallel Port Configuration submenu provides the ability to set the I/O addresses and interrupt levels for the serial (infrared) and parallel ports of your notebook. POINTS n CAUTION I/O addresses, DMA channels, and Interrupt levels can be entered in various ways, including via the BIOS setup utility, the control software for the I/O device, or the hardware. If any two ports or devices have the same I/O address assigned, your notebook will not function normally. Please keep a record of original settings before making any changes in the event that a restoration is required. See your hardware and software documentation as well as the setup utility to determine settings, limitations, etc. To prevent IRQ and address conflicts, avoid changing the default settings. Output Only (Half Duplex) allows information to be transferred in only one direction, from your notebook to the printer or similar device. ECP Mode allows communication with the ECP class of parallel I/O devices. Allows user to set the parallel port base I/O address when the parallel port is Enabled. Disabled Enabled Auto Mode: n n n Output Only Bi-directional ECP [Bi-directional] I/O address: n n n 378 - 37F 278 - 27F 3BC - 3BF IRQ 5 IRQ 7 [378 - 37F] Interrupt: n n [IRQ 7] Allows user to set the parallel port interrupt when the parallel port is Enabled. 15 LifeBook C Series Notebook BIOS Keyboard/Mouse Features Submenu of the Advanced Menu The Keyboard/Mouse Features submenu is for selecting the power-on state for the Numlock key. Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Keyboard/Mouse Features Numlock: [Off] Select power-on state for Numlock. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 6. Keyboard/Mouse Features Submenu Table 6: Fields, Options and Defaults for the Keyboard/Mouse Submenu of the Advanced Menu Menu Field Numlock: Options n n Default [Off] Description Sets the NumLock function state when the computer completes booting. On Off 16 Advanced Menu Video Features Submenu of the Advanced Menu The Video Features Submenu is for choosing the display. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Main Advanced Video Features Display: Compensation: [Internal Flat Panel] [Disabled] Select display terminal. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 7. Video Features Submenu Table 7: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu Menu Field Display: Options n Default [Internal Flat Panel] Description Selects where the video signal will be routed. n n Internal Flat Panel External Simultaneous Disabled Enabled Compensation: n n [Disabled] Enables or disables video compensation. 17 LifeBook C Series Notebook BIOS Internal Device Configurations Submenu of the Advanced Menu The Internal Device Configurations submenu allows the user to enable or disable IDE ports and Wireless LAN. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Internal Device Configurations IDE Controller: Modem Controller: LAN Controller: *Wireless LAN: [Both] [Enabled] [Enabled] [Enabled] [Disabled] No IDE ports are enabled [Primary] Only primary IDE port is enabled. [Secondary] Only secondary IDE port is enabled. [Both] Both primary and secondary IDE ports are enabled. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit * The Wireless LAN option appears on Wireless LAN models only. Figure 8. Internal Device Configuration Submenu Table 8: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu Menu Field IDE Controller: Options n n n n Default [Both] Description Enables or disables IDE controllers. Disabled Primary Secondary Both Disabled Enabled Disabled Enabled Disabled Enabled Modem Controller: LAN Controller: n n [Enabled] Enables or disables the modem. n n [Enabled] Enables or disables the LAN device. Wireless LAN: n n [Enabled] Enables or disables the Wireless LAN device (wireless LAN models only). 18 Advanced Menu CPU Features Submenu of the Advanced Menu The CPU Features Submenu configures the system processor. Note that this submenu only appears in certain configurations, based upon the system CPU. PhoenixBIOS Setup Utility Security Power Savings Exit CPU Features Item Specific Help Main Advanced SpeedStep(TM) Technology: On Battery: On AC: [Enabled] [Battery Optimized] [Maximum Performance] Select Enhanced Intel(R) SpeedStep(TM) Technology enabled or disabled. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 9. CPU Features Submenu Menu Field SpeedStep(TM) Technology: Options n n Default [Enabled] Description When Disabled is selected, CPU speed is fixed to battery optimized speed. When Enabled is selected, CPU speed and battery use can be selected from On Battery and On AC. [. . . ] To view all devices related to a source, press [Enter]; to view all devices related to all sources, press [Ctrl] + [Enter]. To change the order, highlight one source by using the [up] or [down] cursor keys and then press the [+] or [-] key to change the order number for that source. Pressing [d] removes from the list a device that is not installed. Be sure to save your changed order when you exit the BIOS setup utility. NOTE: Be aware that if you use the CD-ROM drive as the first boot device, certain files may be overwritten, depending upon your operating environment. Exiting from Boot Menu When you have finished setting the boot parameters with the Boot menu, you can either exit from the setup utility or move to another menu. [. . . ]