User manual TOSHIBA SATELLITE 2590CDT FIELD REPLACEABLE UNIT DOCUMENTATION

[. . . ] ErgoTrac is a trademark of Fujitsu PC Corporation. The following are registered trademarks of IBM Corporation: IBM, IBM PC AT, IBM PS/2. The following are registered trademarks of Microsoft Corporation: MS, MS-DOS, Windows 98. PCMCIA is a trademark of the Personal Computer Memory Card International Association. [. . . ] When Sound is Enabled, this option is available allowing the user to set the base I/O address for the FM device. When Sound is Enabled, this option is available allowing the user to set the interrupt for the sound device. When Sound is Enabled, this option is available allowing the user to set the DMA channel for the sound device. When Sound is Enabled, this option is available allowing the user to set the DMA channel for the sound device. Four Base I/O address: FM I/O address: Interrupt: 1st DMA channel: 2nd DMA channel: 220-22F; 240-24F; 260-26F; 280-28F. DMA 0; DMA 1; DMA 3; DMA 5. [220-22F] [388-38B] [IRQ 5] [DMA 1] [DMA 5] 71 Section Four Video Features Submenu The Video Features Submenu is for setting the display parameters. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See page 51. ) Table 4-9 shows the names of the menu fields for the Video Features submenu, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Video Features Display Compensation: [Flat-Panel] [Disabled] Select display terminal. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 4-9 Video Features Submenu 72 LifeBook C Series from Fujitsu C o n f i g u r i n g Yo u r L i f e B o o k C S e r i e s Table 4-9 Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu Menu Field Options Default Description Display: Compensation: Flat-Panel; CRT; Simultaneous. [Flat-Panel] [Disabled] Selects where the video signal will be routed. Enables or disables compensation which controls spacing on the display. 73 Four Section Four PCI Configuration Submenu of the Advanced Menu The PCI Configuration Submenu is for setting the interrupt options for legacy ISA devices. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See page 51. ) Table 4-10 shows the names of the menu fields for the PCI Configuration submenu, all the options for each field and a description of the field's function and any special information needed to help understand the field's use. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help PCI Configuration v IRQ Reservation Reserve specific IRQs for use by legacy ISA devices. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 4-10 PCI Configuration Submenu 74 LifeBook C Series from Fujitsu C o n f i g u r i n g Yo u r L i f e B o o k C S e r i e s Table 4-10 Fields, Options and Defaults for the PCI Configuration Submenu Menu Field Options Default IRQ Reservation: Selects the IRQ Reservation Submenu. If you forget the password you will have to contact your support representative to regain access to your secured functions and data. POINT If you make an error when re-entering the password a [Warning] will be displayed on the screen. To try again press the Enter key and then retype the password. Press the Esc key to abort the password setting process. Four 81 CAUTION Entering a password incorrectly 3 times in a row will cause the keyboard and mouse to be locked out and the warning [System Disabled] to be displayed. If this happens restart the computer by turning off and on the power with the power button and use the correct password on reboot. CAUTION If the Power Management Security is Enabled and the Password on Boot is Disabled you will not be able to resume operation from the Suspend or Save-toDisk modes. Section Four Table 4-13 Fields, Options and Defaults for the Security Menu Menu Field Options Default Supervisor Password is: -- Clear. User Password is: Set Supervisor Password: -- [Enter] Clear. Set is displayed when the system supervisor password is set and Clear when it is not. Set is displayed when the general user password is set, and Clear when it is not. Sets, changes or cancels the Supervisor Password. The Supervisor Password may be up to eight characters long. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Supervisor Password is set it must be used to access the BIOS setup utility. [. . . ] Program An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it. PS/2 An IBM series of personal computers which established a number of standards for connecting external devices such as keyboards and monitors. A hardware component of your computer that holds binary information (both program and data) as long as it has the proper power applied to it. RAM Module A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools. Reset The act of reloading the operating system. [. . . ]