User manual TOSHIBA SG1991

[. . . ] , OWNER S MANUAL Preparation SG-1991 2. 4GHz DIGITAL SPREAD SPECTRUM CORDLESS TELEPHONE DIGITAL ANSWERING SYSTEM Basics Caller ID/Call waiting Answering System Additional Information The FIRST thing to do after unpacking your new cordless telephone is: CHARGE THE BATTERY !Please read and follow the few instructions on PAGE 2 BEFORE YOU DO ANYTHING ELSE. GETTING STARTED: DO THIS FIRST! FIRST, CHARGE THE HANDSET BATTERY!· Set your new phone in an out-of-the-way place near a power outlet where it will not be disturbed. · Plug the AC adaptor into the wall outlet. [. . . ] 1: 1 minute 4: 4 minutes RING TIME 2/4/TS REC TIME ANN/4/1 REC TIME switch ANN (Announce Only): If you set the switch to ANN, the selected OGM will be announced and no message will be accepted. The LED display shows "A". SETTING THE CLOCK The answering machine announces the day and time that each message was recorded during a play back. 1 Press and hold till a beep sounds. 2 Select the day of the week by pressing TIME REPEAT or SKIP . When the correct day is announced (corresponding to the number on the LED display), press TIME . 3 Select the Hour by pressing number ( number ( to Answering System REPEAT or SKIP . When the correct ) appears on the LED display, press TIME . When the correct ) appears on the LED display, press TIME . 4 Select the Minute by pressing 5 Select AM/PM by pressing REPEAT or SKIP . At the correct display ( or ), press TIME . You hear a long beep and the new day and time. NOTES: · You can hear the time currently set by pressing TIME . · If you do not complete the setting procedure within 2 minutes, the setting procedure is cancelled. 43 SETTING THE ANSWERING MACHINE SETTING THE PIN NUMBER To access your answering machine when you are away from home, you need to identify yourself with a Personal Identification Number (PIN). You can select any two digit number between 00 and 99 as your PIN. 1 Press and hold REPEAT PIN LED display shows till a beep sounds in the standby mode. The . SKIP 2 Press or to select the left digit of the PIN. 3 When your desired number appears on the LED display, press 4 Press or to select the right digit of the PIN. 5 When your desired number appears on the LED display, press REPEAT SKIP PIN . PIN . The new PIN you entered will be announced. NOTE: You can check the current PIN by pressing PIN at any time. Answering System 44 USING THE ANSWERING MACHINE PIN TIME TIME PIN IN USE CHARGE SPEAKER MUTE VOLUME/­ VOLUME/+ VOLUME LED Display PLAY/STOP DELETE DIGIT AL CALL ER ID / ANSW CORD ERIN LESS G TELE SYST PHONEM E PLAY / STOP DELETE CID REPEAT SKIP MEMO / 2 WAY REC ANSWER GREETING GREETING REPEAT MEMO SKIP TURNING THE ANSWERING MACHINE ON & OFF Press ANSWER to turn the answering machine on. The number of messages appears on the LED display. The greeting message will be played and you hear a long beep. To turn the answering machine off, press ANSWER . The LED display turns off. NOTE: If the message storage area is full, the LED display shows " " and the system announces "No remaining time". You should delete messages (see page 45). Otherwise, the system cannot record any new messages. Answering System RECORDING THE GREETING MESSAGE You can record a personalized greeting message or use the prerecorded message. When a call is received, the answering machine answers the call and plays the greeting message. 1 Press and hold on the base unit till a beep sounds. Record your greeting message over the microphone. (from 2 seconds up to 30 seconds). GREETING 2 When you finish, press or PLAY/STOP . [. . . ] This limitation does not apply to implied warranties arising under state law. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Some states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to you. 55 REMOTE OPERATION CARDS CUT REMOTE OPERATION OF SG-1991 A Call your machine from touch tone phone. After your machine answers, enter # and security code (PIN) pressing each digit for at least 1 second. [. . . ]