User manual TOSHIBA ST-60

[. . . ] TEC POS Terminal ST-60 SERIES Owner's Manual CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. In einer örtlichen Umgebung kann dieses Gerät Funkstörungen verursachen. Dans un environnement domestique, il peut causer des interférences radio. [. . . ] 7-1 7. 1 HOW TO READ MAGNETIC CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GENERAL MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 8. 1 CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. The contents of this manual may be changed without notification. Please refer to your local Authorized Service representative with regard to any queries you may have in this manual. Microsoft and Windows are registered trademarks of Microsoft Corporation. AMD-K6 is a ragistered trademark of Advanced Mircro Devices, INC. Celeron is a registered trademark of Intel Corporation. 1. INTRODUCTION EO1-12026 1. 1 APPLICABLE MODEL 1. INTRODUCTION Thank you for choosing the TEC ST-60 Series POS Terminal. This POS Terminal contains all the high performance register functions necessary for a specialty store POS terminal and enables the user oriented system configuration. By adopting a high-speed CPU (AMD-K6® 266MHz, AMD-K6®-2 333MHz, or Intel® Celeron® 566MHz) and memory with large capacity, this POS Terminal flexibly accepts the modification corresponding to the future system environment as the user expects. This manual describes the functions and handling of this POS terminal and should be read carefully to help gain maximum performance and life from your POS terminal. Used to set HDD's Master/Slave status when the second HDD is connected to the ST-60. Attached to the Drawer Cable when the option Drawer is connected to the ST-60. (A and B models only) Attached to the Drawer Cable when the option Drawer is connected to the ST-60. (C model only) Attached to the Speaker Cable when the Speaker is connected to the ST-60. (C model with sound function only) Attached to the Scanner Cable when the option Scanner is connected to the ST-60. SPECIFICATION EO1-12026 2. 1 GENERAL SPECIFICATIONS 2. 2. 1 SPECIFICATIONS GENERAL SPECIFICATIONS Description AC 100V-127V +10% -10% 50/60 Hz AC 220V-240V +10% -10% 50/60 Hz AC 100V Input Standby: 72W Operation: 72W (When HS-520 Touch Scanner and LIUST-53 Display Unit are connected. ) 5°C ~ 35°C 10% ~ 80%RH (no condensation) Standard: 295mm(W) x 350mm(D) x 121~335mm(H) (NOTE) With MCR: 330mm(W) x 350mm(D) x 121~335mm(H) (NOTE) 8Kg (standard) 9. 3Kg (With HDD, UPS, and MCR) (1) A and B models Item Supply voltage (Autosensing) Power consumption Operating temperature Relative humidity Dimensions Weight NOTE: The height varies according to the tilt angle of the operator's display. 121 mm: Tilt angle of 0° 335 mm: Tilt angle of 90° (2) C model Item Supply voltage (Autosensing) Power consumption Description AC 100V-127V +10% -10% 50/60 Hz AC 220V-240V +10% -10% 50/60 Hz AC 100V Input Standby: 72W Operation: 76W (When HS-530 Touch Scanner, LIUST-51 Display Unit, and TFTST56 TFT Display Unit are connected. ) 5°C ~ 35°C 10% ~ 80%RH (no condensation) Standard: 295mm(W) x 350mm(D) x 129. 2~343. 2mm(H) (NOTE) With MCR: 330mm(W) x 350mm(D) x 129. 2~343. 2mm(H) (NOTE) 8Kg (standard) 9. 3Kg (With HDD, UPS, and MCR) Operating temperature Relative humidity Dimensions Weight NOTE: The height varies according to the tilt angle of the operator's display. 129. 2 mm: Tilt angle of 0° 343. 2 mm: Tilt angle of 90° 2-1 2. SPECIFICATION EO1-12026 2. 2 ENGINE SPECIFICATIONS 2. 2 ENGINE SPECIFICATIONS A B (1) A and B models Model Item CPU BIOS ROM RAM Capacity Type Socket Secondary Cache Interface Customer's Display Touch Panel Method UPS Hard Disk Drive Floppy Disk Drive LAN interface PC Card MCR NV-RAM AMD K6 266MHz AMD K6-2 333MHz 512KB Flash ROM 8MB as standard on board, Max. 72MB (8MB + 64MB DIMM) EDO 64bits, non-parity, without ECC, non-buffered, 60ns, 3. 3V 168-pin DIMM x 1 Pipelined Burst SRAM 512KB RS-232C x 3, Parallel x 1, USB x 2, Drawer x 2 (24V type), PS-2 x 2 Refer to 1. 1 APPLICABLE MODEL (page 1-1). [. . . ] Do not insert nozzle of an air blower into the magnetic card reader slot. Doing so may damage the scanning head, resulting in the magnetic card reader failure. To help retain the high quality and performance of your POS Terminal, it should be cleaned regularly. The greater the usage on the POS Terminal, the more frequent the cleaning. low usage = weekly: high usage = daily) · Cleaning the Operator's Display Clean the surface of the operator's display with a soft dry cloth or with an electrostatic free cleaner for automated office equipment. [. . . ]