User manual TOSHIBA SX2981

[. . . ] , OWNER S MANUAL Preparation SX-2981 900MHz DIGITAL SPREAD SPECTRUM CORDLESS TELEPHONE DIGITAL ANSWERING SYSTEM Basics Caller ID/Call waiting Answering System Additional Information The FIRST thing to do after unpacking your new cordless telephone is: CHARGE THE BATTERY !Please read and follow the few instructions on PAGE 2 BEFORE YOU DO ANYTHING ELSE. GETTING STARTED: DO THIS FIRST! FIRST, CHARGE THE HANDSET BATTERY!· Set your new phone in an out-of-the-way place near a power outlet where it will not be disturbed. · Plug the AC adaptor into the wall outlet. [. . . ] You must subscribe to the CIDCW services before you can use the following features. The "Call waiting" service can also be used independently. Please contact your local telephone company for details. With Caller ID on Call Waiting, you can see who is calling to decide if you want to interrupt your current conversation to answer the incoming call. 1 Before answering a call, check to see that the caller's name and telephone number are displayed on the screen. To switch to the waiting call, press FLASH on the handset. The first caller is put on hold. FLASH 2 To switch back to the first caller, press again. Caller ID/Call waiting NOTES: · Pressing FLASH without having received a Call Waiting signal may disconnect the current line. · When CIDCW is set to Opt in the Caller ID setup menu (See page 15), pressing FUNCTION after receiving a call waiting call allows you to view a list of ways to handle the new call. Choose an option using the and , and press SELECT to active. 33 CALLER ID/CALL WAITING CALL WAITING OPTIONS Your phone gives you new options for call waiting. At the touch of a button, you can ask callers to hold, drop them or conference them into your current call. You may be required to subscribe to both Call Waiting and Call Waiting Options to use these features. Follow these steps to use call waiting options. This is an example for "Conference". Talk 0:02 TOSHIBA CORP 817-858-3300 Press FUNCTION . You receive a call waiting call. s 1sAsk to Hold 2 Tell Busy 3 Answer /Drop 1 A list of options appears. (For more information on the options, see the table on page 35. ) Select one of six options. To select "Conference", press scroll down to "Conference". 4 Caller ID/Call waiting Press or , or number key (1-6). s 4sConference 5 Drop First 6 Drop Last Press SELECT . or Talk 0:03 Conferenced Press FUNCTION . This option allows you to have a 3-way conference call with your first and second callers. The list of options appears. s 1sAsk to Hold 2 Tell Busy 3 Answer /Drop 1 4 Conference 5 Drop First s 6sDrop Last · To drop 1st caller, press down to "Drop First", then · To drop 2nd caller, press down to "Drop Last", then 5 or scroll . 6 or scroll SELECT . SELECT Talk 2:30 Call Dropped A confirmation screen appears. 34 CALLER ID/CALL WAITING The options you can choose are shown below: No. 1 2 Option Ask to Hold Tell Busy Meaning Prerecorded message asks 2nd caller to hold, and the waiting call is put on hold. Prerecorded message tells 2nd caller you are busy, and the waiting call is disconnected. Disconnects 1st caller and answers 2nd caller. Starts a 3-way conference call with both callers. Disconnects 2nd caller. 3 4 5 6 Answer / Drop 1 Conference Drop First Drop Last NOTES: · When using any of the options listed above, an extra charge might apply. · Not all options are available in all areas. [. . . ] Some states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to you. 52 REMOTE OPERATION CARDS CUT REMOTE OPERATION OF SX-2981 A Call your machine from touch tone phone. After your machine answers, enter # and security code (PIN) pressing each digit for at least 1 second. If you enter # and PIN correctly, your machine sounds invitation tone after the announcement. Now enter the command (# and number) by pressing the keypad. [. . . ]