User manual TOSHIBA TDP-FF1

[. . . ] OWNER'S MANUAL LED PROJECTOR TDP-FF1A Before Using Operations Others Preparations SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLT AGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] · The battery is consumables, it can be recharged approximately 500 times. · It is recommended that you replace to a new battery when the operation time with the battery becomes significantly short. (contact reseller for details) · Do not touch the battery connector. · Be sure to use TLPBP1 battery pack. · Store the battery in an environment without moisture. Avoid very high and very low temperatures. · To protect the environment, dispose of the battery safely. Take the battery to a rechargeable battery recycling center. Before taking it to the center, stick insulating tape to the terminal. Specifications for TOSHIBA Li-ion battery · Model name: TLPBP1 · Output voltage: 7. 4V · Capacity: 4400mAh · Operating temperature: 5°~35°C (41°~95°F) · Dimensions: 138(W)x56(H)x26(D) mm · Weight: 0. 25kg · Always observe the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when handling the battery. Warning 21 Preparations Using the remote control Changing the new lithium battery Remove the battery compartment. Replace the lithium battery. Insert the battery compartment. Be sure to align the battery according to the polarity. Operating the remote control Note Turn on the projector and then the remote control can be used to adjust the OSD, volume, and input select. · The remote control is shipped with a plastic sheet between the battery and its contact. Pull on the sheet to remove it from the remote control. · Remove the battery from the remote control when it will not be used for an extended period. Battery · Before using the battery, please refer to the notes on . · If the remote control stops working, or if its range decreases, replace the battery with new one. · The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. · Do not leave it in hot or humid locations. · Do not get it wet or place on top of wet objects. · In rare cases, ambient conditions could impede the operation of the remote control. If this happens, point the remote control at the main unit again, and repeat the operation. The remote control 22 Placement Placement Styles The factory setting is "floor-mounted front projection. " Set the [Projection mode] in the Default setting menu , in accordance with your needs. · Always observe the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit. Warning Projection Distance and Size Screen Top view a (min length) = projection size (inches) 27. 3403 FF1 uses a fixed lens. projection size (inches) 11 17 25 30 35 40 45 50 60 68 projection distance (m) 0. 40 0. 62 0. 91 1. 10 1. 28 1. 46 1. 65 1. 83 2. 19 2. 49 height (H) (cm) 1. 7 2. 6 3. 8 4. 6 5. 3 6. 1 6. 9 7. 6 9. 1 10. 4 Side view Lens center Note: 110% offset condition a is the distance (m) between the lens and the screen, and corresponds to a range of 0. 4 m to 2. 5 m. H is the height from the image bottom to the center of the lens. 23 Preparations Use the figures, tables, and formulas below to determine the projection size and projection distance. (Projection sizes are approximate values for full-size picture with no keystone adjustment. ) Connection Before connection · · · · Read the owner's manual of the device you are connecting to the projector. Some types of computer cannot be used or connected to this projector. Turn off the power of both devices before connecting. [. . . ] · · · · · Is the lens dirty?Is the projection distance within the projector's supported range?Is the projector's screen placement angle tilted too far?Are the sharpness or sampling phase adjustments off? No audio Picture not displayed correctly Picture blurred Part of picture out of focus Colors too light Bad shading Remote control doesn't work · Are the color, tint, R-level, G-level, or B-level adjustments off? [. . . ]