User manual TOSHIBA TDP-S2

[. . . ] TABLE OF CONTENTS Safety Instructions Introduction Image Resolution Compatibility Unpacking the Projector Usage Guidelines If You Need Assistance Setting up the Projector Connecting a Computer Connecting a Video Player Powering up the Projector and Adjusting the Image Turning Off the Projector Using the Projector Basic Image Adjustment Using the Remote Control Adjusting the Projector Using the Keypad and Remote Buttons Using the On-Screen Menus Display Menu Audio Menu Image Menu Controls Menu Language Menu Status Menu Maintenance & Troubleshooting Cleaning the Lens Replacing the Projection Lamp Replacing the Batteries in the Remote Control Using the Security Lock Troubleshooting iii 1 1 2 2 4 5 7 9 11 13 14 15 15 15 17 18 20 21 23 24 27 29 30 33 33 33 36 36 37 i Ta b l e o f C o n t e n t s Appendix Specifications Accessories Portable and Laptop Activation Chart Using Video Mirroring with a PowerBook Computer Projected Image Size Index 41 41 42 43 48 49 51 ii SAFETY INSTRUCTIONS Please read and follow all safety instructions provided BEFORE using your new projector. Failure to comply with safety instructions may result in fire, electrical shock, or personal injury and may damage or impair protection provided by equipment. Please save all safety instructions. Safety Definitions: · Warning: Statements identify conditions or practices that could result in personal injury. · Caution: Statements identify conditions or practices that could result in damage to your equipment. Safety Symbols: Attention: For information about usage of a feature, please refer to the User's Guide. Warning: Hot surface. Do not touch. An arrow pointing to the lamp door on the projector. Safety Terms: · Warning: Don't look directly into the lens when the lamp is turned on. ·Warning: To replace the lamp, turn the projector off by unplugging the power cord. [. . . ] If you turn Resize off (by highlighting it in the Image menu and clicking the left or right mouse button to select "off"), the image may be either cropped or too small for the screen. 24 For video sources, Resize allows you to select from among four different re-sizing options. The default is Standard, which resizes the image from its original version to fit a standard 4x3 aspect ratio screen. Widescreen Letterbox preserves the 16x9 aspect ratio of the original theater version, but the image is placed in a 4x3 space, so black bars appear at the top and bottom of the image. Enhanced Widescreen also preserves the aspect ratio of the original theater version and is designed to be used with content that is Enhanced for Widescreen TVs. This option yields more detail than Widescreen Letterbox. Native reduces the Standard size to match the height of Enhanced Widescreen. Manual Sync The projector adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto Image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually: 1 Turn Auto Image off. 2 Highlight Manual sync, then press the left or right mouse button repeatedly until the image is sharp and free of streaks. Manual Tracking The projector adjusts tracking automatically to match the video signal from your computer. However, if the display shows evenly spaced, fuzzy, vertical lines or if the projected image is too wide or too narrow for the screen, try turning Auto Image off then back on again. If the image is still bad, try adjusting the tracking manually: 1 Turn Auto Image off. 2 Highlight Manual tracking, then press the left or right mouse button repeatedly until the fuzzy vertical bars are gone. NOTE: The Manual Sync, Manual Tracking, Horiz. Position options are available only for analog computer sources. The projector sets these options automatically for digital computer and video sources. 25 U s i n g t h e P r o j e c t o r Horizontal position Follow these steps to manually adjust the horizontal position: 1 Turn Auto Image off. 2 Highlight Horizontal position, then press the left mouse button to move the image right or press the right mouse button to move the image left. Positioning adjustments are saved when you power off the projector. Vertical position Follow these steps to manually adjust the vertical position. 2 Highlight Vertical position, then press the left mouse button to move the image down or press the right mouse button to move the image up. Positioning adjustments are saved when you power off the projector. 26 Controls Menu Display Audio Image > Controls > Language Status Video standard Standby time 1 minute Ceiling projection off Rear projection off Default source computer 1 analog Auto source select off Plug and Play off Display messages on Display startup screen on FIGURE 18 Controls menu Video Standard When Video standard is set to Auto, the projector attempts to pick the video standard (NTSC, NTSC 4. 43, PAL, PAL-M, PAL-N, PAL-60, or SECAM) automatically based on the input signal it receives. (The video standard options may vary depending on your region of the world. ) If the projector is unable to detect the correct standard, the colors might not look right or the image might appear "torn. " If this happens, manually select a standard by clicking the left or right mouse button and cycling through the standards. Standby Time NOTE: If you already know the video standard used in your geographical area, it's often best to manually select it. This option lets you select how long the lamp stays on and the blank screen is displayed when the projector enters standby mode before the projector turns off. Select among instant, 1, 5, 10, 15 and 30 minutes and 1 and 2 hours by clicking the left or right mouse button and cycling through the options. Ceiling Projection When you turn Ceiling Projection on, the projector turns the image upside down for ceiling-mounted projection. Highlight Ceiling Projection, then click the left or right mouse button to turn this feature on and off. 27 U s i n g t h e P r o j e c t o r Rear Projection When you turn Rear Projection on, the projector reverses the image so you can project from behind a translucent screen. Highlight Rear Projection, then click the left or right mouse button to turn this feature on and off. Default Source Default Source toggles among Computer 1 analog, Computer 1 digital, Computer 2, and Video. [. . . ] To turn on video mirroring for the first time: 1 Open the Monitors control panel; click on Monitor 2. 3 Open the Control Strip, then click on the monitor icon. 4 Select "Turn Video Mirroring On. " Now you can turn video mirroring on and off from the Control Strip without having to open the Monitors control panel again. When using video mirroring and high color graphics such as slide shows, the projected image occasionally might turn black and white. [. . . ]