User manual TOSHIBA TDP-S35

[. . . ] OWNER'S MANUAL DATA PROJECTOR (SVGA / With Document Camera) Others Maintenance Operations Preparations TDP-S35 TDP-SC35 (SVGA) Before Using Before Using SAFETY PRECAUTIONS Before Using The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] H is the height from the image bottom to the center of the lens. projection distance a (m) height (H) min length max length (cm) (zooming max) (zooming min) 1. 4 1. 62 4. 0 2. 1 2. 44 5. 9 2. 8 3. 25 7. 9 3. 5 4. 06 9. 9 5. 25 6. 09 14. 9 7. 0 8. 12 19. 8 8. 75 10. 15 24. 8 10. 5 -- 29. 7 Conversion adapter BNC-pin (not supplied) Computer Document camera Computer DVD video recorder, etc. Notes · COMPUTER terminals 1 and 2 function identically. · For TDP-SC35, the document camera should be connected to COMPUTER terminal 2. · The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2. 20 21 Preparations Operations Turning the power on and off Connecting the power cord Notes · The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p. 31 . · The first time you use the projector after purchase, after the start-up screen disappears, the Language menu is displayed p. 24 . 1 Insert the power cord connector into the AC IN socket of the projector. Insert the power cord plug into a wall or (Supplied) Power cord connector other power outlet. 2 Removing the lens cover Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat. Turning the power off 1 Press the ON/STANDBY button. A message appears on the screen, confirming that you wish to shut off the power. This message will disappear after a moment. (This operation is no longer valid after the message disappears. ) 2 Turning the power on Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode. 1 Turn on the main power switch The ON indicator will change to orange, indicating standby mode. TEMP LAMP FAN When cooling lamp TEMP LAMP FAN (Green) During internal cooling TEMP LAMP (Off) After cooling complete TEMP LAMP (Off) FAN (Green) FAN (Off) 2 Press the ON/STANDBY button. The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the start-up screen appears. Control panel Remote Control Start-up screen B (Orange) C (Orange) A During cooling, the LAMP indicator flashes. In this state, the power cannot be turned back on. After the LAMP indicator goes off, the cooling fan continues to operate for a short while, in order to expel excess internal heat. If you are in a hurry, there is no problem with unplugging the power cord or turning off the main power switch in this state. In standby mode B C Note CAUTION · Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight. · Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. · Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. · The projector consumes about 9W of power in standby. We recommend that you unplug the power cord or turn off the main power switch if you will not be using the projector for an extended period. PRECAUTION · If the power cord is unplugged before cooling is complete, give the lamp time (about 5 minutes) to cool before plugging it back in. [. . . ] p. 20 · Are the sharpness or sampling phase adjustments off?p. 27 p. 30 Image is dark Colors too light Bad shading Remote control doesn't work · Are the brightness or contrast adjustments off?p. 30 · Is the lamp nearing the end of its service life?p. 33 · Are the color, tint, R-level, G-level, or B-level adjustments off? [. . . ]