User manual TOSHIBA TDP-TW100

[. . . ] TDP-TW95 TDP-TW100 OWNER'S MANUAL DATA PROJECTOR Others Maintenance Operations Preparations Before Using Before Using SAFETY PRECAUTIONS Before Using 3 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] (In the latter case, the LAMP, TEMP, and FAN indicators light in orange for 3 seconds. ) · When Wireless or USB input is selected, the [Key Lock] cannot be set to [Off] with the [RETURN] button on the projector. Note · The Easy setup automatically switches off when [Ceiling] or [Rear ceiling] is selected for projection mode. [Lamp power] When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder. ) Set this option to use the projector, for example, at high altitude (over 1, 500 meters above sea level). · Do not set Fan mode to [High] when using the projector at a lower altitude. 42 43 Operations Using the menus (Continued) Displaying Information (Status display) This displays information about the input signal, lamp use time, etc. "Yes": displayed, "No": not displayed How to use the USB terminal The supplied wireless LAN USB adapter allows users to connect the projector to a computer via wireless communication, which supports IEEE802. 11b/g wireless LAN p. 46 . (Toshiba does not guarantee the operation of all computers that are IEEE802. 11b/g compliant. ) This projector can connect with a commercial USB memory and a USB memory card reader that are USB2. 0 compliant, a digital camera or the like and display the JPEG files saved in those devices. p. 54 (Toshiba does not guarantee the operation of all USB 2. 0-compliant devices. ) To connect or disconnect a USB device, use the following procedure: Item Projector Input Mode name Resolution Frequency Sync Signal format Video mode Lamp time Lamp reset count Total time Version Description Input source name RGB input mode [Note 1] Resolution (in dots) Sync frequency Sync signal polarity [Note 2] Y/PB/PR signal format Color method of video signal Time of lamp use [Note 3] The count for lamp replacement The total time that this projector is used. Firmware version [Note 4] Computer Y/PB/PR Video S-video Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Yes No No No No Yes No Yes Yes Yes Yes Yes No No No No No Yes Yes Yes Yes Yes Yes No No No No No Yes Yes Yes Yes Yes Wireless/ USB Yes No No No No No No Yes Yes Yes Yes Connecting USB device Plug the USB device. Make sure the orientation is correct then plug the USB device in until it stays securely. USB device Notes 1: The mode of supported RGB signals p. 87 is shown. 2: Sync signal polarity shown as P (positive) or N (negative) for [H/V]. 3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time. ) When the displayed time approaches 2, 000 hours, consult with a dealer about getting replacement for: TLPLW9 for TDP-TW95 or TLPLW10 for TDP-TW100 (sold separately). 4: [Version] shows the version of the projector's internal control program. This version is referred to for customer service, etc. q Switch the input to Wireless/USB and press the MENU button twice to display the Setting display (2), then select and run Unplug device in the Control setting menu. The processing for disconnecting a USB device starts. w The message "Safe to remove the USB device" appears on the screen. e Unplug the USB device. Be sure to perform the above operations. Disconnecting a USB device during operation may cause a malfunction or data corruption. Note · The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again. Notes · The projector may not recognize a supported USB device. In such a case, unplug the USB device then re-plug it. · The USB terminal does not support the supplied mouse remote control receiver or a commercial mouse controller. · A USB hub is also not supported. Precaution · Disconnecting the power plug while the USB device is operating may cause a malfunction or data corruption. 44 45 Operations Disconnecting USB device Setting up the wireless LAN Functions The following functions are available via wireless communications, when the wireless LAN USB adapter and dedicated Wireless Utility software p. 63 included with this projector are used. Note: A wireless LAN USB adapter except the supplied one (or recommended by Toshiba) does not work with this product. Please ask your dealer about the available wireless LAN USB adapter. 1) Displaying a computer's screen via the projector The computer's desktop screen can be sent, as well as the screens of a variety of software applications, to the projector for display. Likewise, the sound being played on a computer can also be sent to the projector. 2) Displaying an image saved on a computer via the projector JPEG files can be sent to the projector for display. [. . . ] p. 36 p. 21 Image is dark Colors too light Bad shading · Are the brightness or contrast adjustments off?p. 36 · Is the lamp nearing the end of its service life?p. 44 · · · · Are the color, R-level, G-level, or B-level adjustments off?p. 38 Is the lamp nearing the end of its service life? [. . . ]