User manual TOSHIBA TDP-TW300

[. . . ] TDP-TW300 OWNER'S MANUAL DATA PROJECTOR Others Maintenance Operations Preparations Before Using Before Using SAFETY PRECAUTIONS Before Using 3 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] <Auto-setting>: Switches on/off the auto-setting function when the EASY SETUP button is pressed or when Power on Easy setup is set to ON. <Power on Easy setup>: Switches on/off the Easy setup operation when the power is turned on. Note · The Easy setup automatically switches off when [Ceiling] or [Rear ceiling] is selected for projection mode. When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. Auto input search Power on Easy setup [On Off] Off Off Off Lamp power Fan mode Sets the lamp power. Sets the cooling fan speed. Low Standard On Standard High Off [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector, for example, at high altitude (over 1, 500 meters above sea level). Wireless standby Switch on/off the wireless LAN while the projector is in standby. Remote control When two or more projectors are used and controlled by the remote control respectively, this menu sets the code for the projector and the remote control. [ or : Enter setting mode] [ : Select item] [ : Select from 1, 2, 3, 4] [ :Confirm] [ :Select OK to end] Press [Cancel] to return. Key lock Lock the control panel buttons. [ or : Enter setting mode] Select On/Off] [ :Confirm] Press [Cancel] to return. [ [ : Select item] [ :Select OK to end] : [Wireless standby] When [Wireless standby] is set to [On], the wireless LAN is switched to the standby state as the projector enters standby. While the wireless LAN is in standby, the projector can be powered on using the remote control function of the Wireless Utility. When [Wireless standby] is set to [Off], the projector cannot be powered on with the remote control function of the Wireless Utility. [Remote control] Sets a remote control code from 4 types. You can set each code respectively for up to 4 projectors. To switch codes, set the same code for the projector and the remote control. A remote control code is applied after the setting is done. · You cannot operate the remote control if the codes of the projector and the remote control do not match. Reset all Password Press . (The password and user logo are not reset. ) Resets all adjustments and settings to their factory settings. Yes Password function p. 36 Off When [Password] is [On], the Password Setting screen is displayed. No On Remote control code setting for remote control Remove the battery cover and set the same remote control code switch as the projector. p. 16 (Use a screwdriver with thin tip to set. ) Detailed description [Blackboard mode] Projects the image in colors more like projecting on a screen. [Key lock] Protect from operating errors by locking on the control panel buttons of the projector. (The remote control operations are available. ) Control panel operations are locked after the setting is done. · To release the key lock, press the control panel's RETURN button for 10 seconds. The key lock is released with a beep sound. Precaution · The projected image may differ depending on the type, color, and material of the blackboard and wall even if the selected color is the same as the projected screen. 44 45 Operations [Lamp power] Using the menus (Continued) The control setting menu This menu sets items regarding wired LAN. By this setting, you can transmit operation status messages from the projector to the specified E-mail address. Item Wired LAN [ : Wired LAN setting] Description [ : Select item] Projector name: Enter a character string (0 to 64 characters) using numeric keys of the remote control. [. . . ] · Is a wireless LAN PC card not supported by the projector inserted?The operation of cards other than the supplied product is not guaranteed. p. 49 · Are the transmission mode and channel properly configured?p. 54 · Are there any obstructions between the computer and projector? [. . . ]