User manual TOSHIBA TLP621-2

[. . . ] For maximum protection, repack the set as it was originally packed at the factory. Avoid Volatile Liquid Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time. Moisture Condensation Never operate this unit immediately after moving it from a cold location to a warm location. [. . . ] The signal source, size and display position to display sub-pictures can be changed from the menu screen. 52 VOL / ADJ ENTER CT-90106 EXIT / P. MODE Displaying Information Information on the input signal source, etc. , can be displayed. CALL CONTENTS 39 Press CALL. The information described below is displayed. The information display turns off when the CALL button is pressed again. Remote control Status display Input - current input source H-resolution - the horizontal resolution of the input signal (at RGB input) V-resolution - the vertical resolution of the input signal (at RGB input) H-frequency - the horizontal frequency of the input signal (at RGB input) V-frequency - the vertical frequency of the input signal (at RGB input) Sync - the polarity of the sync signal (at RGB input) Video mode - the color mode of the video signal (at Video, S-Video input) Signal format- the formatting of the Y/PB/PR signal (at Y/PB/PR input) Lamp time - the elapsed usage time of the lamp Version - the version of the firmware Shutter - the shutter speed of the document imaging camera (at document imaging camera input) Operations ON / STANDBY INPUT KEYSTONE AUTO SET FREEZE MUTE PIP CALL RESIZE CALL MENU VOL / ADJ ENTER CT-90106 EXIT / P. MODE Notes · The information displayed is not refreshed even if it changes. To refresh the information, turn off the information display, then turn it back on. · The information display turns off if any other operation is performed. · The "Lamp time" shows an approximate time for lamp replacement. (It should not be used as a lamp warranty time counter. ) If the time indicated here nears 1500, contact your store of purchase about obtaining a replacement lamp (TLPL55, sold separately). · The "Lamp time" can be reset when the lamp is replaced. · The "Version" is the version of the control program used in the projector and is used for servicing, etc. Operating the presentation mode CONTENTS 40 You can change the slide, for the presentation on the computer, by using the remote control when connecting the projector to the computer with the supplied USB cable. 1 Connect a computer to the projector with the supplied USB cable. Also connect the RGB cable and the audio cable if necessary. 23 USB connector Computer for presentation CONTROL USB AUDIO Operations USB cable (supplied) To USB connector Be sure to connect in the proper direction. To USB port Notes · This function is available with O. S (operating system) of Windows 98/98SE, Windows Me, Windows 2000 or Mac OS9 with a USB port as standard. · When connecting to the computer's USB port for the first time, a message asking you to insert the Windows98 or Windows 98SE CD-ROM may appear on the computer's monitor screen, depending on whether or not the device driver is installed. To operate GUIDE MENU, refer to page 42 . CONTENTS 44 The relationship between input source and item Yes: Adjustable -: Not displayed Analog RGB Y/PB/PR Adjust the image brightness. Adjust the gain of the document imaging camera. Contrast Brightness Phase Color Camera gain Shutter Auto 50Hz 60Hz Bright True color Keystone COMPUTER Analog RGB Y/PB/PR VIDEO S-VIDEO CAMERA ADJ. Adjust the document imaging camera's gain. Select a shutter speed below to decrease the flickering of the document imaging camera's picture. SET The shutter speed is set automatically. SET The shutter speed is fixed to 50 Hz. SET The shutter speed is fixed to 60 Hz. SET The picture is set with its brightness priority. SET The picture is set with its color quality priority. SET SET SET SET SET SET : COMPUTER connector is selectable with the INPUT button. [. . . ] Clean the lens with a blower or lens cleaner, etc. Focus the picture by turning the focus ring. Set the shutter speed on the menu screen. Cause · The remote control is not facing the remote sensor. [. . . ]