User manual TOSHIBA TP50F61

[. . . ] If you did not receive all of the items, or any of the items are damaged or broken, please contact your Toshiba dealer. In addition, you may need to purchase other audio or video cables to connect your equipment. See "Connecting your TV" on page 4 for more information. Please read all the safety and operating instructions carefully before you begin. Exploring your new TV You can operate your TV by using the buttons on the front panel or the remote control. [. . . ] When channel programming is complete, the message "COMPLETED (channel or cable number)" appears. Press Channel v or w to view the programmed channels. Exit RESET CAP/TEXT 1/2 FAV CODE MTS SLEEP MUTE Adding and erasing channels manually After you've programmed the channels, you can add or erase specific channels. Select the channel you want to add or erase using Channel + or ­. If adding channels, you must select the channel to add by using the Channel Number buttons. Press MENU, then press or CH to display the SET UP menu. Press v or w to highlight ADD/ TV / CABLE TV ERASE. Press or to select ADD or ADD / ERASE ADD ERASE ERASE, whichever function you want to perform. Repeat steps 1-4 for other channels you want to add or erase. POWER TV VCR CABLE CH RTN 1 4 7 2 5 8 CH + 3 6 9 ENT 100 0 Channel Numbers Setting up your TV Channel +/­ VOL ­ MENU/ ENTER VOL + Menu CH ­ EXIT RECALL TV/VIDEO FAV Exit RESET CAP/TEXT 1/2 FAV Changing channels To change the channel, you can: · change the programmed channels using the remote control · select a channel directly using the remote control · scan the channels using the TV buttons To change to the next programmed channel: Press Channel + or ­ on the TV or remote control. To change to a specific channel (programmed or unprogrammed): Press the Channel Number buttons (0-9 and 100). For example, to select channel 125, press the 100 button, the 2 button, and the 5 button. CODE MTS SLEEP MUTE 12 3I70401D P12-21 12 16/08/2001, 15:55 Using the TV's features Adjusting the channel settings Switching between two channels You can switch between two channels without entering an actual channel number each time. Select the first channel you want to view. Press to or display the V-CHIP menu. CH PICTURE AUDIO SET UP OPTION V-CHIP BLOCKING PIN CODE SELECT END [0-9] EXIT RESET Note: 4. Use the Channel Number buttons (0-9) to enter your PIN code. If you are accessing the V-Chip menus for the first time, select a four-digit number to be your PIN code. The BLOCKING menu appears. CH PICTURE AUDIO SET UP OPTION V-CHIP ENABLE BLOCKING SET RATING BLOCKING OPTION NEW PIN CODE CHANNEL BLOCK SELECT ON OFF START START START START ADJUST MENU/ ENTER Menu/ Enter CH ­ EXIT RECALL TV/VIDEO FAV Blocking programs by ratings The Motion Picture Association of America (MPAA) uses a rating system to qualify motion picture content. Television broadcasters employ a rating system to qualify the content of television programs, as well. The MPAA, Youth TV and TV ratings work with the V-Chip feature and allow you to block out programming above the rating limits you determine. RESET CAP/TEXT 1/2 FAV Exit 15 3I70401D P12-21 15 16/08/2001, 15:56 Appendix Using the TV's Features CODE MTS SLEEP MUTE Setting up your TV To change your PIN code: 1. Press MENU, then press or to display the OPTION menu. Use the Channel Number buttons (0-9) to enter your PIN code. If you are accessing the V-Chip menus for the first time, select a four-digit number to be your PIN code. Press v or w to highlight NEW PIN CODE and press or to display the NEW PIN CODE menu. Use the Channel Number buttons (0-9) to enter a new code. [. . . ] ("THI") make the following limited warranties. These limited warranties extend to the original consumer purchaser or any person receiving this set as a gift from the original consumer purchaser and to no other purchaser or transferee. Limited Ninety (90) Day Warranty Important Safeguards Appendix Appendix Using the TV's Features Setting up your TV Using the Remote Control Connecting your TV TACP and THI warrant this product and its parts against defects in materials or workmanship for a period of ninety (90) days after the date of original retail purchase. During this period, TACP and THI will repair a defective product or part, without charge to you. You must deliver the entire set to an Authorized TACP/THI Service Station. [. . . ]