User manual TOSHIBA TP61E80

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the distance between the equipment and receiver. [. . . ] · If using an indoor antenna or if TV reception is very poor, the closed caption decoder may not appear or may appear with strange characters or misspelled words. In this case, adjust the antenna for better reception or use an outdoor antenna. 22 5K60101B [E] (P13-23) 22 20/4/04, 15:47 To memorize channels This TV/DVD is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the TV/DVD's memory. In addition to normal VHF and UHF channels, this TV/ DVD can receive up to 113 Cable TV channels. To use this TV/DVD with an antenna, set the TV/CABLE selection to the TV position. When shipped from the factory, this selection is in the CABLE position. 0­9 MENU /// TV/CABLE selection Automatic memory tuning or Press or to select the "AUTO CH MEMORY", then press . The TV will begin memorizing all the channels available in your area. 1 Press MENU in the TV mode, then press to select option. SETUP/MENU TV operation TV/CABLE CABLE MEMORY VOL ­ VOL + AUTO CH CH + ADD/ DELETE VOL + CH ­ TV/CABLE AUTO CH MEMORY CABLE ADD/ DELETE / / / / MENU 2 Press CH + or to select "TV/CABLE". / / / MENU To ADD/DELETE channels TV/CABLE CABLE MEMORY AUTO CH ADD/ DELETE CH ­ 1 Press press or . to select "ADD/DELETE", then / / / / MENU 3 Press or to select "TV" or "CABLE". CH + TV/CABLE CABLE MEMORY TV - VHF/UHF channels CABLE - Cable TV channels VOL ­ VOL + VOL + CH ­ AUTO CH ADD/ DELETE / / / MENU TV/CABLE AUTO CH MEMORY TV ADD/ DELETE 2 Select the desired channel to be added or deleted using Direct channel selection (0­9) or CH + / ­. 1 2 5 8 0 3 CH + / / / / MENU 4 7 6 9 CH ­ 4 Press MENU repeatedly until the menu screen is cleared. SETUP/MENU Cable TV chart The chart below is typical of many cable system channel allocations. 3 Press or to select "ADD" or "DELETE", whichever function you want to perform. ADD VOL ­ VOL + CH 001 0-9 / / / / / MENU 23 5K60101B [E] (P13-23) 23 20/4/04, 15:47 TV operation Setting the V-Chip An age limitation can be set to forbid children to watch programs according to "TV RATING" and "MOVIE RATING" level set. To use the V-Chip function, you must register a password. Notes: · If you forget the password, you cannot set the V-Chip. · To avoid forgetting the password, write it down and keep in the safe place. 0­9 MENU CANCEL /// ENTER To register password To change password or to select 1 Press MENU, then press option. SETUP/MENU 1 In the V-CHIP menu, press or to select "CHANGE PASSWORD", then press . CH + V-CHIP SET VOL ­ VOL + VOL + NEW PASSWORD :­­­­ CH ­ V-CHIP V-CHIP SET CHANGE PASSWORD OFF / / / / MENU / / / MENU 2 Press CH + or to select "PASSWORD". 2 V-CHIP SET NEW PASSWORD :­­­­ Enter the new password using Number buttons (0­9), then press ENTER. 1 4 7 2 5 8 0 3 6 CHANGE PASSWORD ENTER CH ­ 9 NEW PASSWORD :­­­­ 0­9/ENTER/CANCEL/MENU 3 Enter the password (4 digits) using Number buttons (0­9), then press ENTER. · If you put a wrong number, press CANCEL. 1 4 7 2 5 8 0 ENTER CANCEL 0-9/ENTER/CANCEL/MENU 3 6 9 V-CHIP SET NEW PASSWORD 3 Enter the same password again using Number buttons (0­9) for safety, then press ENTER. 1 : 2 5 8 0 3 6 9 ENTER 4 7 CHANGE PASSWORD CONFIRM PASSWORD 0­9/ENTER/CANCEL/MENU : " " appears instead of the number. 0-9/ENTER/CANCEL/MENU 4 Enter the same password again for the safety, then press ENTER. The DVD startup screen will appear on the screen. "Reading" display will change to "No Disc". (If DVD disc has already loaded, playback will start automatically. ) No Disc Reading · A menu screen will appear on the TV screen, if the disc has a menu feature. Press C/D or B/A to select title, then press ENTER. Title is selected and play commences. 3 Press OPEN/CLOSE. The disc tray opens. 6 Press STOP to end playback. 3Resuming facility · The unit records the stopped point, depending on the disc. Press PLAY to resume playback (from the scene point). · If you press STOP again or unload the disc ("3" appears on the screen. ), the unit will clear the stopped point. 4 Place the disc on the disc tray. With the playback side down 3 To start playback in the stop mode Press PLAY. · There are two different disc sizes. Place the disc in the correct guide on the disc tray. If the disc is out of the guide, it may damage the disc and cause the unit to malfunction. [. . . ] You must also deliver the entire product to a TACP Authorized Service Station. You are responsible for all transportation for the set to and from the Service Station. Limited Two (2) Year Warranty of Picture Tube TACP further warrants the picture tube in this product against defects in materials or workmanship for a period of two (2) years after the date of original retail purchase. During this period, TACP will replace a defective picture tube without charge to you except that if a defective picture tube is replaced after ninety (90) days from the date of the original retail purchase, you pay labor charges involved in the replacement. You are responsible for all charges involved in the replacement. [. . . ]