User manual TOYOTA JEAN

[. . . ] 3 How to change the power plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Part names. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Part names and their functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Quick adviser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Doing so could cause an injury. Pull the thread from the thread spool, and then hold it with one hand while passing it around the thread guide with the other hand, as shown. Thread guide Hold in place with your finger. Pass the thread end through the hole in the bobbin as shown. Place the bobbin on the thread winding spindle so the groove aligns with the shaft projection. Hole Thread winding spindle Thread Groove Bobbin Shaft projection 2 Sewing preparations Spool pin ( 2 ) Thread winding spindle ( 7 8 10 ) Main power switch ( 1 6 ) Slide the thread winding spindle in the direction of the arrow until it snaps into place. 6 Foot controller ( 7 9 ) Turn on the machine. Main power switch 7 1 While holding the thread end, begin pressing on the foot controller with your foot. 2 After the thread has been wound around the bobbin about 10 times, release the foot controller to stop winding. Foot controller 15 Threading the lower thread Open the bobbin case cover, and insert the bobbin into the bobbin case. If the bobbin is incorrectly inserted into the bobbin case, the stitching will not be sewn correctly. 1 Turn off the sewing machine. Main power switch 2 Pull the bobbin case cover towards yourself. Bobbin case cover Insert the bobbin so that it rotates counterclockwise. 11/75 to 16/100 with the needle threader. (Needle No 14/90 is included when the sewing machine is purchased. ) The needle cannot be threaded if the thread is too thick for the needle. For details on possible needle and thread combinations, refer to “Relationship between the needle, thread and fabric, and adjusting the thread tension” on page 27. zz Preparing to use the needle threader 1 Turn the handwheel towards yourself until the needle is in its highest position. ** If the needle is not in its highest position, the needle cannot be threaded. 2 Turn the pattern selection dial to “7” (straight stitch). Firmly tighten the needle clamp screw with the screw driver for the needle plate. Pin Screw driver for the needle plate Needle clamp screw Flat surface zz Correct needle selection Good needle If a faulty needle is used, not only could it impair the sewing performance, but it could also damage the needle plate or hook, or break the needle. ** Incorrect stitching or thread breaking, try replacing the needle. ÍFaulty needle The entire needle is bent 26 The point of the needle is crushed / worn away The point of the needle is bent Relationship between the needle, thread and fabric, and adjusting the thread tension The quality of the sewing finish will improve if the needle and thread are changed to match the type of fabric. Follow the directions in the table below. Thin fabrics Relationship between the needle, thread and fabric No. 80 Normal back cloth Quipler Georgette Lawn Lace, etc. zzFor XXX15C Reference thread tension -3 -1 +1 Normal fabrics No. 50 Curtains Denim Quilting Fleece Tweed Felt, etc. 2 Sewing preparations Thread Fabric Normal front cloth Broad Soft denim Satin Pile Gingham, etc. -2 -1 +2 +1 +2 +3 +4 Upper thread tension dial -1 ~ -3 +1 ~ +3 zzFor XXX15D/ SuperJ15 -2 -3 -1 ~ -3 -1 ~ +3 • Use a ball point needle for the sewing alignment of stretch fabric. • Please purchase any needles not included as accessories, after checking they are specified as home-use sewing machine needles. • Use the same kind of threads for upper/lower thread. • The bigger the needle number is , the thicker the needle is, the bigger the thread number is, the thinner the thread is. [. . . ] 3 Check that the needle correctly enters the hole in the needle plate. ** If the bobbin case is not installed correctly, the handwheel does not turn smoothly. If this occurs, remove the needle plate and bobbin case, and attach them again. 4 Maintenance 45 Changing light bulb Warning Before changing the light bulb, use the main power switch to turn off the sewing machine, remove the power plug from the outlet, and then wait until the bulb cools. Not doing so could cause a burn or electric shock. 8 1 Loosen the screw with a + screw driver of your own, and take off the face cover in the direction of the arrow. Screw Face cover 8 2 Turn the light bulb counterclockwise as the arrow in the diagram and remove. Turn the new light bulb clockwise to install. [. . . ]