User manual TP-LINK TL-SL2218WEB

[. . . ] User's Guide TL-SG2109WEB 9-port Gigabit Web Smart Switch TL-SL2210WEB 8+2G Gigabit Web Smart Switch TL-SL2218WEB 16+2G Gigabit Web Smart Switch TL- SL2428WEB 24+4G Gigabit Web Smart Switch TL-SL2452WEB 48+4G Gigabit Web Smart Switch COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK Technologies Co. , Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK Technologies Co. , Ltd. [. . . ] 2) Please make sure the TFTP server in operation. 3) Breaks should be avoided during file transfer; otherwise, the switch may get damaged. 5. 3. 1. 3 Reboot & Reset This page is showed as below. Figure 5-18 Reboot & Reset 34 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide A prompt will display if a button is pressed. For example, if the button "Softreset" is pressed, a message box will be activated as showed in figure 5-19. Figure 5-19 Message Box 5. 3. 1. 4 User This page provides the interface of configuring username and password. Figure 5-20 User Configuration You are kindly suggested to retype the new password in "Confirm new password" box instead of copying in order to avoid typing mistakes. Notice: 1) Only letters, numbers and punctuations can be input into username and password field, the other characters are considered illegal. The length of username and password ranges from 1 to 16 characters. 2) The initial username and password is supervisor/supervisor. 35 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide 5. 3. 2 Port Setting 5. 3. 2. 1 Port Parameter This page contains the following fields: Figure 5-21 Port Parameter Port Status: Indicates whether the port is operational or non-operational. " Enable" Indicates the port is operational and "Disable" Indicates the port is non-operational. If a port is unused for a long time, it can be set it to be non-operational to cut down energy costs. Notice: You can't manage the switch via the port, which is non-operational, please set the value of the management port to "enable". Port Security: "Enable" Indicates the port will not learn new MAC address and only transmit the frames from the MAC address it has learned. " Disable" Indicates it will learn new MAC address. 36 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide Notice: If you haven't set the static MAC address, you can't enable all of the port security, which will result in an inability to manage the switch. Flow Control: Indicates whether the flow control is enabled or disabled. Duplex Mode: Possible filed values are Auto, 10M HD, 10M FD, 100M HD, 100M FD and 1000M FD (Giga port support), "HD" stands for halfduplex and "FD" stands for full-duplex. "Auto" means auto negotiation. Further explanation: 1) By operating on fields in the All Ports line expediently, you can set the values of all ports in the corresponding field. Some other setting pages offer the same function. 2) Parameters of Trunk member ports are configured with default value (see the Appendix B table) and cannot be configured here (see port 5 and 6 in the figure for example). For SFP, the Duplex Mode is set to "1000M FD" and cannot be modified. 5. 3. 2. 2 Port Statistic This page displays the port statistic, it contains the following entries: Figure 5-22 Port Statistic 37 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide Tx Collisions: The number of collision events seen by the MAC. This counter is applicable in half-duplex only. Tx Ucast: The number of frames sent that have a unicast destination MAC address. Tx Mcast: The number of frames sent that have a multicast destination MAC address. Tx Bcast: The number of frames sent that have a broadcast destination MAC address. Rx (G Pkts): The number of good frames received. Rx Ucast: The number of frames received that have a unicast destination MAC address. Rx Mcast: The number of frames received that have a multicast destination MAC address. Rx Bcast: The number of frames received that have a broadcast destination MAC address. [. . . ] If the priority mode is set to "Disable", the priority rule cannot be configured. 5. 3. 6. 2 Port-Based Priority This page is revealed when the "Port-Based" mode is configured. Port-Based priority Port: Indicates the switch port number. Priority Class: In port-based priority mode, the switch ports are classified into four priority classes: lowest, lower, higher and highest. All the packets entering from the port of the switch are forwarded in the corresponding priority queue. 58 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide Further Explanation When priority rule is configured as "weighted", a 1, 2, 4, 8 weighting is applied to forward these four classes of packets. 5. 3. 6. 3 Port Default Priority This page is revealed when the "IEEE802. 1p" mode is configured. [. . . ]