User manual TP-LINK TL-SL5428 INSTALLATION GUIDE

[. . . ] TL-SL5428 24-Port 10/100 + 4-Port Gigabit Managed Switch Rev: 1. 0. 0 1910010123 COPYRIGHT & TRADEMARKS ® is a registered Specifications are subject to change without notice. trademark of TP-LINK TECHNOLOGIES CO. , LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. Copyright © 2008 TP-LINK TECHNOLOGIES CO. , LTD. [. . . ] Console>enable Password: [privileged level password] Console# 4-7 4 Command Line Interface Configuration Commands Configuration commands are privileged level commands used to modify switch settings. These commands modify the running configuration only and are not saved when the switch is rebooted. To store the running configuration in non-volatile storage, use the copy running-config startup-config command. The configuration commands are organized into different modes: · Global Configuration - These commands modify the system level configuration, and include commands such as hostname and snmp-server community. · Access Control List Configuration - These commands are used for packet filtering. · Interface Configuration - These commands modify the port configuration such as speed-duplex and negotiation. · Line Configuration - These commands modify the console port and Telnet configuration, and include command such as parity and databits. · VLAN Configuration - Includes the command to create VLAN groups. To enter the Global Configuration mode, enter the command configure in Privileged Exec mode. The system prompt will change to "Console(config)#" which gives you access privilege to all Global Configuration commands. Console#configure Console(config)# To enter the other modes, at the configuration prompt type one of the following commands. Use the exit or end command to return to the Privileged Exec mode. Table 4-2 Configuration Modes Mode Line Access Control List Class Map Interface MSTP Policy Map Command line {console | vty} access-list ip standard access-list ip extended access-list mac class map spanning-tree mst-configuration policy map Prompt Console(config-line)# Console(config-std-acl) Console(config-ext-acl) Console(config-mac-acl) Console(config-cmap) Console(config-mstp)# Console(config-pmap) Console(config-sg-radius)# Console(config-sg-tacacs+)# Console(config-vlan) Page 4-11 4-138 4-140 4-145 4-198 4-120 4-154 4-200 4-101 4-167 interface {ethernet port | port-channel id| vlan id} Console(config-if)# Server Group aaa group server {radius | tacacs+} VLAN vlan database 4-8 Entering Commands 4 For example, you can use the following commands to enter interface configuration mode, and then return to Privileged Exec mode Console(config)#interface ethernet 1/5 . Console(config-if)#exit Console(config)# Command Line Processing Commands are not case sensitive. You can abbreviate commands and parameters as long as they contain enough letters to differentiate them from any other currently available commands or parameters. You can use the Tab key to complete partial commands, or enter a partial command followed by the "?" character to display a list of possible matches. You can also use the following editing keystrokes for command-line processing: Table 4-3 Command Line Processing Keystroke Ctrl-A Ctrl-B Ctrl-C Ctrl-E Ctrl-F Ctrl-K Ctrl-L Ctrl-N Ctrl-P Ctrl-R Ctrl-U Ctrl-W Esc-B Esc-D Esc-F Delete key or backspace key Function Shifts cursor to start of command line. Shifts cursor to the left one character. Terminates the current task and displays the command prompt. Shifts cursor to the right one character. Deletes all characters from the cursor to the end of the line. Repeats current command line on a new line. Enters the next command line in the history buffer. [. . . ] Formerly called Group Address Registration Protocol. Generic Multicast Registration Protocol (GMRP) GMRP allows network devices to register end stations with multicast groups. GMRP requires that any participating network devices or end stations comply with the IEEE 802. 1p standard. Group Attribute Registration Protocol (GARP) See Generic Attribute Registration Protocol. IEEE 802. 1D Specifies a general method for the operation of MAC bridges, including the Spanning Tree Protocol. IEEE 802. 1Q VLAN Tagging--Defines Ethernet frame tags which carry VLAN information. It allows switches to assign endstations to different virtual LANs, and defines a standard way for VLANs to communicate across switched networks. IEEE 802. 1p An IEEE standard for providing quality of service (QoS) in Ethernet networks. The standard uses packet tags that define up to eight traffic classes and allows switches to transmit packets based on the tagged priority value. IEEE 802. 1X Port Authentication controls access to the switch ports by requiring users to first enter a user ID and password for authentication. IEEE 802. 3ac Defines frame extensions for VLAN tagging. IEEE 802. 3x Defines Ethernet frame start/stop requests and timers used for flow control on full-duplex links. [. . . ]