User manual TRANSCEND TS0MFLRD7

[. . . ] 6 To Safely Remove the Multi-Card Reader To Remove in Windows 98/98SE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 To Remove in Windows 2000, Me, and XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 To Remove in Mac OS and Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Windows installs the files needed to use your device. 3 4. Four Removable Disk drives with newly assigned drive letters appear in My Computer. The Multi-Card Reader is ready for use. For the Multi-Card Reader with 0MB Flash Disk, only three newly assigned Removable Disk drives appear in My Computer. To safely remove the memory card, you must make sure that no LED is blinking (no data are being transmitted). WARNING: Never remove or insert a memory card or disconnect the USB cable while data are being transmitted. To avoid improper shutdown, open the transmitted file from its new location to ensure transmission has been completed. To Use with Windows Me and XP The Multi-Card Reader is a driver-free device for Windows Me and Windows XP. You can connect it to an available USB port directly (or via the USB extension cable) and don't have to install a special driver. Windows Me and Windows XP will detect the device and automatically install all the associated files required for its use. The process sequence is listed below: 4 Four Removable Disk drives with newly assigned drive letters appear in My Computer. The Multi-Card Reader is ready for use. For a Multi-Card Reader with 0MB Flash Disk, only three newly assigned Removable Disk drives appear in My Computer. To safely remove the memory card, you must make sure that no LED is blinking (no data are being transmitted). WARNING: Never remove or insert a memory card or disconnect the USB cable while data are being transmitted. To avoid improper shutdown, open the transmitted file from its new location to ensure transmission has been successful. 5 To Use with Mac OS 9. x 1. Connect the Multi-Card Reader to an available USB port directly (or via the USB extension cable). Insert a memory card into the Multi-Card Reader. You can then use the memory card as if it were a Mac HardDisk. With a built-in Flash Disk (128MB or 256MB), you can use the Multi-Card Reader as if it were a Mac HardDisk without a memory card inserted. To safely remove the memory card, drag and drop the corresponding disk icon onto the trashcan icon. After the disk icon disappears, you can remove the memory card. WARNING: Never remove or insert a memory card or disconnect the USB cable while data are being transmitted. To avoid improper shutdown, open the transmitted file from its new location to ensure transmission has been successful. To Use with Mac OS X 10. 1. 2 or Later The Multi-Card Reader is a driver-free device for Mac OS X 10. 1. 2. You can connect it to an available USB port directly (or via the USB extension cable) and you do not have to install a special driver. [. . . ] Click the icon on the system tray. 2. The Safely remove USB Mass Storage Device pop-up message appears. The Safe To Removed Hardware blurb appears. The Multi-Card Reader is now ready to be removed. If you attempt to remove the Multi-Card Reader without following the above steps, the Unsafe Removal of Device message (in Windows 2000) appears. To Remove in Mac OS and Linux When there is no memory card in the Multi-Card Reader, you can disconnect the device from the USB port at any time. 8 LED Indicators LED #4 MMC/SD/MS LED #1 Red: Blinking: LED #2 Green: Blinking: LED #3 Green: Blinking: LED #4 Green: LED #3 SmartMedia Power On LED #2 CF/Microdrive LED #1 Power/Flash Data traffic on built-in flash disk CompactFlash or Microdrive inserted Data traffic on CompactFlash or Microdrive SmartMedia card inserted Data traffic on SmartMedia card Secure Digital, miniSD (with adapter), MultiMediaCard, RS-MMC (with adapter), Memory Stick, Memory Stick PRO, Memory Stick Duo (with adaptor) and Memory Stick PRO Duo (with adaptor) inserted Blinking: Data traffic on Secure Digital, miniSD (with adapter), MultiMediaCard, RS-MMC (with adapter), Memory Stick, Memory Stick PRO, Memory Stick Duo (with adaptor) and Memory Stick PRO Duo (with adaptor) 9 Specifications Power Supply ·············································· DC 5V from USB port Slots for memory cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]