User manual TRANSCEND TS16GCF100I DATASHEET

[. . . ] Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) Description The Transcend CF100I is a High Speed industrial Compact Flash Card with high quality Flash Memory assembled on a printed circuit board. Features · CompactFlash Specification Version 4. 1 Complaint · RoHS compliant products · Single Power Supply: 3. 3V±5% or 5V±10% · Operating Temperature: -40 C to 85 C o o o o Placement · Storage Temperature: -55 C to 100 C · Operating Humidity (Non condensation): 0% to 95% · Storage Humidity (Non condensation): 0% to 95% · Operation Modes: PC Card Memory Mode PC Card IO Mode True IDE Mode · True IDE Mode supports: Ultra DMA Mode 0 to Ultra DMA Mode 4 Multi-Word DMA Mode 0 to Multi-Word DMA Mode 4 PIO Mode 0 to PIO Mode 6 (Series of ­P Only support PIO Mode 0 to PIO Mode 4, please see Order Information) · True IDE Mode: Fixed Disk (Standard) · PC Card Mode: Fixed Disk (Standard) · Durability of Connector: 10, 000 times · MTBF: 4, 000, 000 hours Dimensions · Support Wear-Leveling to extend product life · Support S. M. A. R. T (Self-defined) · Support Security Command · Compliant to CompactFlash, PCMCIA, and ATA standards · Mechanical Shock Test: 1500G · Vibration Test: 20G (Peak-to-Peak) 20Hz to 2000Hz (Frequency) Transcend Information Inc. 1 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) Order information Part Number Interface Transfer Mode Ultra DMA mode 0~4 True IDE mode TS128M~16GCF100I Multi-Word DMA Mode 0~4 PIO Mode 0 ~ 6 PC Card mode (PCMCIA) 80ns, 100ns, 120ns, 250ns TS128M~16GCF100I-P True IDE mode PIO Mode 0 ~ 4 Fixed Disk (Standard) Fixed Disk (Standard) Fixed Disk (Standard) Fixed Disk (Standard) PC Card mode (PCMCIA) 250ns C. H. S. Table Capacity 128MB 256MB 512MB 1GB 2GB 4GB 8GB 16GB C 246 493 987 1974 3949 7899 15798 33149 H 16 16 16 16 16 16 16 15 S 63 63 63 63 63 63 63 63 Transcend Information Inc. 2 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) Transcend Transcend Information Inc. 3 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) Block Diagram Transcend Information Inc. 4 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) Pin Assignments and Pin Type Transcend Information Inc. 5 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state signals not to consume current. 2) The signal should be grounded by the host. [. . . ] When the bit is 1, interrupts from the CompactFlash Storage Card are disabled. This bit also controls the Int bit in the Configuration and Status Register. This bit is set to 0 at power on and Reset. Bit 0: this bit is ignored by the CompactFlash Storage Card. Transcend Information Inc. 52 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) Card (Drive) Address Register (Address 3F7h[377h]; Offset Fh) This register is provided for compatibility with the AT disk drive interface. It is recommended that this register not be mapped into the host's I/O space because of potential conflicts on Bit 7. Bit 7: this bit is unknown. Implementation Note: Conflicts may occur on the host data bus when this bit is provided by a Floppy Disk Controller operating at the same addresses as the CompactFlash Storage Card. Following are some possible solutions to this problem for the PCMCIA implementation: 1) Locate the CompactFlash Storage Card at a non-conflicting address, i. e. Secondary address (377) or in an independently decoded Address Space when a Floppy Disk Controller is located at the Primary addresses. 2) Do not install a Floppy and a CompactFlash Storage Card in the system at the same time. 3) Implement a socket adapter that can be programmed to (conditionally) tri-state D7 of I/0 address 3F7h/377h when a CompactFlash Storage Card is installed and conversely to tristate D6-D0 of I/O address 3F7h/377h when a floppy controller is installed. 4) Do not use the CompactFlash Storage Card's Drive Address register. This may be accomplished by either a) If possible, program the host adapter to enable only I/O addresses 1F0h-1F7h, 3F6h (or 170h-177h, 176h) to the CompactFlash Storage Card or b) if provided use an additional Primary / Secondary configuration in the CompactFlash Storage Card which does not respond to accesses to I/O locations 3F7h and 377h. With either of these implementations, the host software shall not attempt to use information in the Drive Address Register. Bit 6 (-WTG): this bit is 0 when a write operation is in progress; otherwise, it is 1. Bit 5 (-HS3): this bit is the negation of bit 3 in the Drive/Head register. Bit 4 (-HS2): this bit is the negation of bit 2 in the Drive/Head register. Bit 3 (-HS1): this bit is the negation of bit 1 in the Drive/Head register. Bit 2 (-HS0): this bit is the negation of bit 0 in the Drive/Head register. Bit 1 (-nDS1): this bit is 0 when drive 1 is active and selected. Bit 0 (-nDS0): this bit is 0 when the drive 0 is active and selected. Transcend Information Inc. 53 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) CF-ATA Command Set CF-ATA Command Set summarizes the CF-ATA command set with the paragraphs that follow describing the individual commands and the task file for each. Command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Check Power Mode Execute Drive Diagnostic Erase Sector Flush Cache Format Track Identify Device Idle Idle Immediate Initialize Drive Parameters Key Management Structure Read Key Management Read Keying Material Key Management Change Key Management Value NOP Read Buffer Read DMA Read Long Sector Read Multiple Read Sector(s) Read Verify Sector(s) Recalibrate Request Sense Security Disable Password Security Erase Prepare Security Erase Unit Security Freeze Lock Security Set Password Security Unlock Seek Code E5 or 98h 90h C0h E7h 50h ECh E3h or 97h E1h or 95h 91h B9 (Feature 0-127) B9 (Feature 80) B9 (Feature 81) 00h E4h C8h 22h or 23h C4h 20h or 21h 40h or 41h 1Xh 03h F6h F3h F4h F5h F1h F2h 7Xh FR ­ ­ ­ ­ ­ ­ ­ ­ ­ Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ ­ SC ­ ­ Y ­ Y ­ Y ­ Y Y Y Y ­ ­ Y SN ­ ­ Y ­ ­ ­ ­ ­ ­ Y Y Y ­ ­ Y Y Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ Y CY ­ ­ Y ­ Y ­ ­ ­ ­ Y Y Y ­ ­ Y Y Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ Y DH Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y ­ ­ ­ ­ ­ ­ ­ ­ Y LBA ­ ­ Y ­ Y ­ ­ ­ ­ ­ ­ ­ ­ ­ Y Y Y Y Y Status Support Support Support NOT Support Support Support Support Support Support NOT Support NOT Support NOT Support NOT Support Support Support NOT Support Support Support Support Support Support Support Support Support Support Support Support Support #2 #2 #2 #2 #2 #2 #3 #1 #1 #1 #3 Note Transcend Information Inc. 54 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card (TS128M ~ 16GCF100II) (TS128M ~ 16GCF100 ) 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Set Feature Set Multiple Mode Set Sleep Mode Standby Standby Immediate Translate Sector Wear Level Write Buffer Write DMA Write Long Sector Write Multiple Write Multiple w/o Erase Write Sector(s) Write Sector(s) w/o Erase Write Verify EFh C6h E6h or 99h E2 or 96h E0 or 94h 87h F5h E8h CAh 32h or 33h C5h CDh 30h or 31h 38h 3Ch Y ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ Y ­ ­ ­ Y ­ ­ Y ­ Y Y Y Y Y ­ ­ ­ ­ ­ Y ­ ­ Y Y Y Y Y Y Y ­ ­ ­ ­ ­ Y ­ ­ Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y ­ ­ ­ ­ ­ Y ­ ­ Y Y Y Y Y Y Y Support Support Support Support Support Support Support Support Support Not Support Support Support Support Support Support #3 #1: This command is optional, depending on the key Management scheme in use. #2: Use of this command is not recommended by CFA #3: Use of this command is not recommended. #4: When the controller gets this command, it will skip this command and return 0x50. [. . . ] Bits 2-0: Maximum Advanced PCMCIA I/O Mode Support Indicates the maximum I/O timing mode supported by the card. Value 0 1 2 3 4-7 Maximum PCMCIA IO timing mode Supported 255ns Cycle PCMCIA I/O Mode 120ns Cycle PCMCIA I/O Mode 100ns Cycle PCMCIA I/O Mode 80ns Cycle PCMCIA I/O Mode Reserved Reserved Bits 5-3: Maximum Memory timing mode supported Indicates the Maximum Memory timing mode supported by the card. Value 0 1 2 3 4-7 Maximum Memory timing mode Supported 250ns Cycle Memory Mode 120ns Cycle Memory Mode 100ns Cycle Memory Mode 80ns Cycle Memory Mode Reserved Idle - 97h or E3h This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. If the sector count is non-zero, it is interpreted as a timer count with each count being 5 milliseconds and the automatic power down mode is enabled. [. . . ]