Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TRANSTEL GROUP RTS-100-N3RU. We hope that this TRANSTEL GROUP RTS-100-N3RU user guide will be useful to you.
Lastmanuals help download the user guide TRANSTEL GROUP RTS-100-N3RU.
Manual abstract: user guide TRANSTEL GROUP RTS-100-N3RU
Detailed instructions for use are in the User's Guide.
[. . . ] If DS1 does not light up, call TransTel.
Installation 1. Record the telephone number assigned by the cellular carrier on the instruction sheet attached to the inside of the RTS-100 door. The ESN (electronic serial number) of the transceiver has already been recorded at the factory. Connect earth ground to the external chassis lug. . [. . . ] If you cannot complete a call, dial 611 to make sure that cellular service has been activated. If you hear a hi/lo tone, check antenna connector, antenna cabling, and antenna position.
6.
Poor signal.
1. Check antenna location and change if necessary. Replace omnidirectional antenna with Yagi or other directional antenna.
7. 9.
10.
All rights reserved:
TransTel Group, Inc. Norcross, Georgia 30093 Tel. : 770 368-8343 Fax: 770 368-8382
Page 4
Antenna Alignment The Test Mode feature of the RTS-100-N3RU is useful for positioning the cellular antenna to achieve maximum signal strength. A cellular handset must be plugged into J3 to do this. Place unit in Test Mode by turning off power at the handset, moving switch SW1 to "Test", and turning power on again. Several sets of alternating numbers will be displayed on the cellular handset. The last three digits of the six-digit number indicate signal strength. To check for proper antenna position, move the antenna and check the readout. As the signal improves, the numbers will increase. When using a directional antenna, rotate the antenna in 15-degree increments, pause to allow the signal to stabilize, and check the readout. After a full circle is completed, note the optimum antenna position. Power the unit down from the handset, move SW1 to "Normal", mount the antenna, and power the RTS unit up from the handset. Programming The RTS is designed to be easily programmed in User Mode or Test Mode provided a cellular handset is available. User-Mode programming is described in the Motorola NAM programming guide. To program the RTS in Test Mode, proceed as follows: 1. Connect any Motorola handset for Series III or Series IV radios at J3 of the RTS I/O board. Power the unit down from the handset, move SW1 to "Test", and power the unit up again. [. . . ] The red LED/switch and the transceiver will be turned on at the same time. Your RTS-100-N3RU is equipped with a circuit that monitors the battery voltage to prevent sulfurization of the battery. When the battery voltage drops below 10. 5 volts, the cellular transceiver is turned off after a few seconds. To energize the RTS unit, you must apply 115 VAC at the J2 terminal block. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TRANSTEL GROUP RTS-100-N3RU
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TRANSTEL GROUP RTS-100-N3RU will begin.
