User manual TREK BIKES INCITE 6I-8I QUICK START GUIDE

[. . . ] Maximum 240 . CAD (i only) Functions 3 INSTAllATION Stem mount Handlebar mount Speed sensor Cadence sensor Figure 3- location on bicycle of sensors and computer Tools needed: · Electrical tape · Slot-type screwdriver · Phillips-type screwdriver · Scissors 4 Installation Placing the computer on the handlebar The Trek Incite 9i or 11i computer can be mounted on the handlebar or on the stem (Figure 3). To install the computer on handlebar 1. Select the bar clamp that fits your bike. 31. 8mm bars: large clamp 25. 4mm and 26. 0mm: small clamp 22. 2mm bar: small clamp with rubber shim 2. Insert the handlebar clamp into the back of the computer base (Figure 4) and slide it towards the front of the base. Figure 4- Clamp and friction pad in computer base 3. [. . . ] Wrap the wire around the front brake cable, diverting the determined amount. Continue routing the wire, either by wrapping around the fork or frame tube, or attach the wire to the fork or frame tube with electrical tape. As needed, solidify the wire attachment with either nylon ties or electrical tape. Figure 8- Trim excess nylon tie length 8 Installation Attaching the sensors The magnet must pass across the line on the sensor (Figure 9). These instructions are written for the front wheel, but apply equally to installing the magnet and cadence sensor which go on the left crank and the frame's chainstay (Figure 10). To install the sensor 1. Orient the sensor so that the clearance between the sensor and the magnet is between 1 to 3mm. The sensor can be rotated around the fork about 45 degrees. If needed, the sensor and magnet can be moved up or down the spoke and fork to change the amount of clearance. Attach the sensor with nylon ties, but do not fully tighten. With the computer in the computer base, check the alignment of the sensor 1. 0 3. 0mm Figure 9- Magnet alignment and clearance Figure 0- Magnet placed on crankarm, aligned with sensor on 9 Installation chainstay and magnet by spinning the wheel and noting if the computer is displaying speed. If the computer shows current speed, the sensor is reading the magnet. If the computer is not displaying a value, realign the sensor and magnet until one is displayed. Repeat step 2 to change again. Easy setup (reSet) 5 CLK TME AVG MAX TRP ODO MH Set Mode To set Clock 1. Hold Set· "12" or "24" flashes. Cycle Mode 12 and 24 interchange on the screen. MPH F CLK TME AVG MAX TRP AVG 4. Push Set· to select The clock appears on the screen with the Hour flashing. The computer returns to current speed. Figure 5- CloCK screen 6 Easy setup (reSet) CLK TME AVG MAX TRP ODO MH Set RESTART- gETTINg REAdy TO RIdE Your computer stores data for two intervals- since last ReSet and since last ReStart. ReStart sets only the Trip data to zero. The trip modes include · TRP · TME · MAX This operation sets all four values to zero, allowing the computer to display information for a single ride. Mode To ReStart (set the Trip data to zero) 1. Hold Set·, and do not let up until after completing step 3. The Max setting ReStarts at `0'. F MPH CLK TME AVG MAX TRP AVG Figure 6- TrP screen reStart CLK TME AVG MAX TRP ODO MH Set AddITIONAl INfORMATION Changing mode Mode Once the computer is programmed and installed, it is very easy to use. To change to different modes (functions), simply Cycle the Mode button until the desired function appears, shown by the spelled name of the function. Removing the computer from the computer base The computer is held on its base by a flexible snap. To remove the computer, press firmly on the computer (not on the base) in a rearward direction. using the computer in wet weather Bicycle computers function on electricity. [. . . ] Have your helper mark the floor at the valve stem. While you sit on the bike, have the helper roll the bike forward one revolution of the wheel, so that the valve stem is again directly over the floor. Mark the new location of the valve stem. Measure the distance between the marks, in millimeters. [. . . ]