User manual TRENDNET TE100-S16E

[. . . ] Using crossover cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 PORT SPEED & DUPLEX MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 TECHNICAL SPECIFICATIONS. . . . . . . . . . . . . . . 17 RJ-45 PIN SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 ii ABOUT THIS GUIDE Congratulations on your purchase of the 16-port 10/100Mbps NWay Fast Ethernet Switch. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network in a highly flexible desktop package. Purpose This manual discusses how to install your 16-port 10/100Mbps NWay Fast Ethernet Switch. Terms/Usage In this guide, the term " Switch" (first letter upper case) refers to your 16-port 10/100Mbps NWay Fast Ethernet Switch, and "switch" (first letter lower case) refers to other Ethernet switches. Overview of this User's Guide Chapter 1, Introduction. Helps you get started with the basic installation of the Switch. Chapter 3, Identifying External Components. [. . . ] The Switch is expandable by cascading two or more switches together. As all ports support 200Mbps, the Switch can be cascaded from any port and to any number of switches. The Switch is a perfect choice for site planning to upgrade to Fast Ethernet in the future. Ethernet workgroups can connect to the Switch now, and change adapters and hubs anytime later without changing the Switch or reconfigure the network for migrating to Fast Ethernet. The Switch combine dynamic memory allocation with store-and-forward switching scheme to ensure that the buffer is effectively allocated for each port, while 4 controlling the data flow between transmit and receive nodes to guarantee against all possible packet loss. The Switch is an unmanaged 10/100Mbps Fast Ethernet Switch that offers solutions for increasing Ethernet workgroup bandwidth. The Switch's other key feature including the following: ?Uplink/ MDI-II (media dependent interface) ?port for uplinking to another switch, hub or repeater. result of complete frame checking and error frame filtering, this scheme prevents error packages from transmitting among segments. allows each port to auto-sense connection speed (10/100Mbps), which provides automatic and flexible connection for the network. IEEE 802. 3x flow control for full-duplex connections ?and Back Pressure flow control for half-duplex connections. Data forwarding rate per port is at wire-speed ?Data filtering rate eliminates all error ?packets, runts, etc. , per port at wire-speed for 100Mbps speed. Up to 8K active MAC address entry table per ?port with self-learning and table-aging. ? UNPACKING AND SETUP This chapter provides information for the Switch. unpacking and setup Unpacking Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items: One 16-port 10/100Mbps NWay Fast Ethernet Switch One external power adapter 6 This User's Guide If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the Switch can be performed using the following steps: ?The installation surface must be able to ? [. . . ] The Link/ACT LED indicator lights green for connecting to 100Mbps speed. The LED lights amber for connecting to 10Mbps speed. The FDX/COL LED indicator lights green for full-duplex connection. The LED remains off for half-duplex connection. 2. Port Speed & Duplex Mode After plugging the cable to a specific port, the system uses auto-negotiation to determine the transmission mode: If the attached device does not support autonegotiation or has auto-negotiation disabled, an auto-sensing process is initiated to select the proper connection speed and the duplex -mode is set to halfduplex. 15 TECHNICAL SPECIFICATIONS General Standards IEEE 802. 3 10Base-T Ethernet IEEE 802. 3u 100 Base-TX Fast Ethernet ANSI/IEEE Std 802. 3 NWay auto-negotiation Protocol Data Transfer Rate CSMA/CD Ethernet: 10Mbps (half duplex) 20Mbps (full duplex) Fast Ethernet: 100Mbps (half duplex) 200Mbps (full duplex) Topology Network Cables Star 10BASE-T: 2-pair UTP Cat. [. . . ]