User manual TRENDNET TEW-AP100PLUS

[. . . ] This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. CE Marking Warning This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 2 11Mbps Wireless LNA Access Point User's Manual Table of Contents 1. INTRODUCTION The Wireless LAN Access Point Features Package Contents 4 5 2. Hardware Installation Physical Details Installation Connecting the AP to your Network 6 6 8 9 3. [. . . ] Click this button will re-boot Access Point. Restore Default Click this button to restore the Access Point default settings. Any setting you may have made through the AP Manager will be lost if this button is clicked. Download This button is used for firmware upgrade capability. If you click the download button to upgrade firmware, the Access Point will reboot automatically after download process. 18 11Mbps Wireless LNA Access Point User's Manual The AP Setup Tab The AP Setup tab allow you to set the wireless configuration items and WEP encryption. If any item had been changed, you need to click Save button to store new settings and then click Reset AP button on General Setup tab to make new settings effect. AP SSID SSID is used to identify the wireless LAN. To communicate, all Wireless stations MUST use the same SSID. Default SSID is GROUPxxxxxx, where xxxxxx are six hexadecimal digits. AP Channel Select the appropriate radio channel from the list provided. The permissible number of channels depends on the Regulatory Domain. (The factory setting is Channel 3) 19 11Mbps Wireless LNA Access Point User's Manual AP Basic Rate Set The basic data transfer rate should be set depending on the speed of your wireless network. If ALL had been chosen, the data rate will up to 11Mbps. And auto fallback will be supported. Enable WEP Enable or disable WEP function. If NO (default), data is NOT encrypted before being transmitted. Encryption Level Select 64-bit or 128-bit WEP encryption. WEP Mode Mandatory or Optional. Authentication Type Select the appropriate value - "Open System" or "Shared Key". Check your Wireless card's documentation to see what method to use. Some Wireless cards do not support both methods. Default Key Select the key you wish to be the default. The default WEP key is 1. Transmitted data is ALWAYS encrypted using the Default Key; the other Keys are for decryption only. Key0, 1, 2, 3 This table is used when encrypting and decrypting data. All stations, including this Access Point, always transmit data encrypted using their default key. The key number (0, 1, 2, 3) is also transmitted. The receiving station will use the key number (0, 1, 2, 3) to determine which key value to use for decryption. If the key value does not match the transmitting station, decryption will fail. 20 11Mbps Wireless LNA Access Point User's Manual The DHCP Client Tab The DHCP Client tab allow you to enable/disable DHCP client. If any item had been changed, you need to click Save button to store new settings. Enable DHCP Client Enable the Access Point to act as a DHCP client. This is the default setting of the AP. Static IP Address If the Access Point act as a DHCP client, and it has a static IP address, fill the address on this field. The default static IP address is 10. 0. 0. 1 Network Mask The Network Mask (Subnet Mask) for the IP Address. The default Network Mask is 255. 0. 0. 0 21 11Mbps Wireless LNA Access Point User's Manual The DHCP Server Tab The DHCP Server tab allow you to enable/disable DHCP server. [. . . ] · TCP/IP is the standard internet protocol. WEP (Encryption) By setting an encryption key in the Access Point, you can prevent wireless packets from being decrypted externally. When connecting to the Access Point with the encryption key you must enter the encryption key from the AP Manager. Firmware Firmware is the name given to the software (programs) built into hardware such as the router, modem, and terminal adapter. This software is built into the hardware, so it can be said to be in-between hardware and software. Protocol Protocols are the procedures and regulations for sending and receiving data between the network terminals. For example, if two computers are communicating, you can send the correct information according to the regulations by formatting all required information. [. . . ]