User manual TRENDNET TEW-P1U1P

[. . . ] Table of Contents Chapter 1 Introduction 1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the Router (Gateway) Address is 0. 0. 0. 0, the Subnet Mask should also be left at 0. 0. 0. 0. If you have a router, enter the Subnet mask for the segment to which the Wireless Print Server is attached. If your network segment has a router or gateways, enter its IP Address here. Otherwise, leave the address as 0. 0. 0. 0. Sets how long the Wireless Print Server should wait before retrying a TCP/IP connection which is lost. Allowable values are from 0 to 255 seconds, with 2 as the default. Set how many attempts at reconnection will be made. After that, the TCP/IP session will be terminated. Allowable values are from 0 to 255, with 254 as the default. Page 42 Configure Server Figure 35: Configure Server Screen Print Server Name Password Change the default name if you wish. The new name must not contain any spaces or blanks. Enter the device password, and again in the Verify field. Once a password is entered, it is required in order to gain access and change the configuration. Non-TCP/IP may be disabled if they are not required on your LAN. The available protocols depend on the Print Server model. Enable Protocols Page 43 Wireless Configuration The settings on this screen must match the other Wireless stations in order for communication to occur. Figure 36: Wireless Screen Page 44 Configuration Regulatory Domain Station name It is illegal to use this device in any location outside of the regulatory domain. This is the same as the Device (Host) Name on the WAN screen. On your PC, some Wireless status screens may display this name as the Access Point in use. To communicate, all Wireless stations MUST use the same SSID/ESSID. Select the value you wish to use on your Wireless LAN. If you experience lost connections and/or slow data transfers you may need to experiment with different channels to see which is the best. Select the correct value for your Wireless LAN. · Ad-hoc mode is used when there is no Wireless Access Point, and each Wireless station communicates directly with other Wireless stations. Infrastructure mode is used when each Wireless station connects to the Wireless Access point. [. . . ] 8. Type a name in the NDPS Manager Name. (e. g. SerMGR in Figure 1 above) Browse the Resident Server and select where you want the NDPS Manager object to be assigned. TECH_50. TeSupp in figure 1 above) Browse the Database Volume and select where you want the NDPS Manager database to be assigned. TECH_50_SYS. TeSupp in figure 1 above) Click Create. [. . . ]