User manual TRENDNET TPL-302E2K

[. . . ] 2 LED INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 QUICK SETUP BUTTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CONNECTING TO NETWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The TPL-302E is not connected to the AC power line. The TPL-302E is goes to firmware upgrade or on pairing. The TPL-302E is the PowerLine addresser. The PCL is not join to PowerLine group The TPL-302E is the PowerLine joiner. The TPL-302E is connected to the Ethernet network The TPL-302E is not connect to Ethernet network The TPL-302E is on transmission data to/from Ethernet network. RJ-45 Ethernet port AC Power plug Quick Setup Button The button is used to setup the TPL-302E to join into the Powerline network group quickly. Resetting the network ID Press the Quick Setup button until all LEDs extinguish (more than 10 seconds), the TPL-302E will reset the network ID setting and generate a random network ID. Always reset the network ID before pairing the TPL-302E. 10/100M Fast Ethernet Port Connect to Ethernet enabled device. AC Power Plug Plugging into the AC power outlet. 2 3 Pairing the TPL-302E When new TPL-302E adapters want to join to existing Powerline Network, press the Quick Setup button on any exist TPL-302E adapter and press the new TPL-302E adapter's Quick Setup button within three seconds at the same time, the Power LED will start blinking, it means the TPL-302E adapters goes to pairing process, when finished the pairing, the Power LED will be steady on. INSTALLATION The 200M Powerline AV to Fast Ethernet Adapter is designed to be simple and easy installation. 10/100M Fast Ethernet Port Connect to Ethernet enabled device. AC Power Plug Plugging into the AC power outlet. LED Indicators Detailed LED description shows on Page 3. Quick Setup Button The button is use to setup the TPL-302E to join into the Powerline network group quickly. 4 5 Connecting to network You can connect the 200M Powerline AV to Fast Ethernet Adapter directly to the PC's network adapter, switch, or any other Ethernet enabled device. Note: The Ethernet port on the Adapter supports 10/100M Auto-MDI/MDIX function, you can use a straight-through or a crossover Ethernet cable when connecting to another Ethernet enabled device. ) Configuration Utility The Powerline AV Utility for Windows OS enables the users to identify TPL-302E devices on the power line network, measures data rate performance, ensures privacy and performs diagnostics by setting user defined secure power line networks. Install Configuration Utility Insert the Powerline AV utility CD into your CD-ROM drive and the Auto-run program will appear. Alternatively this can also be done manually by double clicking the autorun. exe file on the CD. Click the "Install Software" on the menu to install the Powerline AV Utility, the install wizard will begin the software installation. Follow the install wizard instructions completed the Powerline AV Utility install. 6 7 Using the Powerline AV Utility Device Information The Device Information screen shows the device information including the MAC address, Firmware Version and the connected TPL-302E device. To start the Powerline AV Utility, double click the icon desktop, the Configuration Utility will be executed. on the The Configuration Utility was divided into four functions, Device Information, Network Information, QoS, Security, Upgrade and About, for details instruction, follow the below section. Network Information The Network Information screen shows all devices that were on the power line network are listed here. Devices that are active on the current logical network will show a transfer rate and receiver rate. 8 9 QoS QoS requirements are different for various data types such as streaming video or music, voice and raw data. To provide higher QoS for streaming data, priority levels can be set using tags at the beginning of data frames. Virtual Local Area Network (VLAN) 802. 1p priority tags on Ethernet frames are used to specify 8 (0 ­ 7) levels of `user priority'. The 200M Powerline AV to Fast Ethernet Adapter allows 4 levels of Channel Access Priority (CAP (0 ­ 3)). Therefore, the 8 levels of VLAN Ethernet tags must be mapped to the 4 levels of CAP priority, where CAP 3 is the highest priority and CAP 0 is the lowest. CAP 3 priority might be used for voice and network management frames, CAP 2 is used for streaming video and music while CAP 1 and CAP 0 are used for data. Mapping VLAN tags or TOS bits to CAP levels is easily done using the VLAN Priority Mapping function on the QoS tab window. List View The QoS tab includes two list views to provide simple channel access priority (CAP) classification for individual MAC addresses and IP Ports. [. . . ] (The DAK password is show on each TPL-302E's device label). Reset to Default Press the Reset to Default button to restore the factory default network id setting for "TRENDnet". Device Selection Select the device form drop down list will be configure. 12 13 Upgrade Device Selection Select the device form drop down list will be configure. Reboot Device Press the Reboot Device button to reset the node, which will restore the initial factory configuration. About The About screen shows the Powerline AV Configuration Utility information including utility version and release date. Firmware Upgrade To upgrade the firmware, press the Firmware Upgrade button and then locate the two firmware files (PIB file *. pib and firmware file *. nvm), the confirmation windows will pop up, click Yes to start the firmware upgrade or click No to abort the firmware upgrade. 14 15 SPECIFICATIONS Hardware Standards Interface Frequency Band Modulation Speed Supported OS Nodes Encryption LED Dimension (L x W X H) Weight Power Source Consumption Temperature Operating Humidity Certification IEEE 802. 3, IEEE 802. 3u Powerline AV (2. 0) 10/100Mbps AutoMDIX RJ45 Port Power Prongs 2 ~ 30 MHz OFDM, QAM, BPSK, ROBO Powerline: Up to 200Mbps LAN: 10/100Mbps Windows 2000/XP(32/64)/Vista(32bit) Up to 16 client notes 128bit AES Power, HomePlug, Ethernet 78 x 30 x 102 mm (3 x 1. 2 x 4 inches) 140g (5 oz. ) Input: 100~240V AC, 160mA 4. 2 watts (max. ) 0° ~ 40° C (32° ~ 104° F) 0% to 90% (NonCondensing) FCC, CE Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TPL-302E ­ 3 years If a product does not operate as warranted above during the applicable warranty period, TRENDnet shall, at its option and expense, repair the defective product or deliver to customer an equivalent product to replace the defective item. [. . . ]