User manual TRENDNET TPL-401E2K

[. . . ] Table of Contents Chapter 1: Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 2. 1 2. 2 2. 3 2. 4 Powerline Network Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Within 2 minutes (120 sec), push and hold the Sync button on Adapter B for 2 seconds and release it. This will establish connectivity between Adapters B, D, and E by assigning Adapter B's network name/security key to match the network name/security key of Adapters D and E. To verify connectivity between the powerline adapters, make sure that the PL LED on each powerline adapter is on solid (Green, Amber, Red). Please refer to the LED section 1. 5 for details on the LED indicator. Chapter 4: Powerline Configuration Utility The Powerline Configuration Utility is an additional tool that allows you to centrally manage the powerline adapters that are connected to your network. Instead of using a randomly generated key with the Sync button, the utility allows you to manually configure the network name/security key for a single powerline adapter or multiple adapters simultaneously. This tool allows for easy management for multiple powerline adapters in your network. Note: 1. Before installing and using the utility, write down the 16-digit Device Password (DPW) and MAC Address of each TPL-401E powerline adapter as this will be required to apply changes to remote devices discovered in the utility. This is located on the Device Label, please refer to Section 1. 4. Before installing and using the utility, make sure your computer in which you are installing the utility is connected to your network and your TPL-401E adapters are also connected to your network. Make sure all of the TPL-401E powerline adapters are already connected to each other using the procedures in Chapter 2: Product Installation. The utility is only compatible with Windows operating systems. For details, please refer to Section 1. 3. 4. 1 Software Installation 1. Insert the included CD-ROM into your computer's CD-ROM drive. At the CD Autorun Prompt window, click Run Autorun. exe 3. At the CD-ROM menu window, click Install Utility. 4. At the WinPcap installer window, click Next. Note: The Powerline Configuration Utility requires the use of the WinPcap application. If this prompt does not appear, you may already have the WinPcap application installed. If so, please skip over to Step 9. 5. In the Setup Wizard window, click Next. 6. In the License Agreement window, click I Agree. 7. In the Install Options window, click Install. 8. At the Setup Wizard Completion window, click Finish. 9. [. . . ] Please contact the point-of-purchase for their return policies. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. [. . . ]