User manual TRIMBLE 5700 GPS RECEIVER

[. . . ] USER GUIDE Trimble R7 GNSS Receiver Trimble 5700 GPS Receiver ® NORTH AMERICA Trimble Engineering & Construction Group 5475 Kellenburger Road Dayton, Ohio 45424-1099 · USA 800-538-7800 (Toll Free) +1-937-245-5154 Phone +1-937-233-9441 Fax EUROPE Trimble GmbH Am Prime Parc 11 65479 Raunheim · GERMANY +49-6142-2100-0 Phone +49-6142-2100-550 Fax ASIA-PACIFIC Trimble Navigation Singapore Pty Limited 80 Marine Parade Road #22-06, Parkway Parade Singapore 449269 · SINGAPORE +65-6348-2212 Phone +65-6348-2232 Fax www. trimble. com USER GUIDE Trimble R7 GNSS Receiver Trimble 5700 GPS Receiver ® Version 4. 00 Revision A February 2009 F Corporate office Trimble Navigation Limited Engineering and Construction group 5475 Kellenburger Road Dayton, Ohio 45424-1099 USA 800-538-7800 (toll free in USA) +1-937-245-5600 Phone +1-937-233-9004 Fax www. trimble. com Canada This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. Europe This product has been tested and found to comply with the requirements for a Class B device pursuant to European Council Directive 1999/5/EC on R&TTE, thereby satisfying the requirements for CE Marking and sale within the European Economic Area (EEA). These requirements are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential or commercial environment, and to ensure that the equipment is safe Australia and New Zealand This product conforms with the regulatory requirements of the Australian Communications and Media Authority (ACMA) EMC framework, thus satisfying the requirements for C-Tick Marking and sale within Australia and New Zealand. [. . . ] ­ Discontinue charging a battery that gives off extreme heat or a burning odor. ­ Use the battery only in Trimble equipment that is specified to use it. ­ Use the battery only for its intended use and according to the instructions in the product documentation. Charging the Lithium-ion battery The rechargeable Lithium-ion battery is supplied partially charged. Charge the battery completely before using it for the first time. If the battery has been stored for longer than six months, charge it before use. To protect the battery from deep discharge (5 V or less), the receiver is designed to switch batteries or cease drawing power when the battery pack discharges to 5. 9 V. A battery that has reached the deep discharge level cannot be recharged and must be replaced. The following recommendations provide optimal performance and extend the life of your batteries: · · Fully charge all new batteries before use. Do not allow the batteries to discharge below 5 volts. 42 Trimble R7 GNSS and 5700 GPS Receivers User Guide General Operation 4 · · · Do not store batteries in the receiver or external charger unless power is applied. If you must store the batteries, fully charge them before storing and then recharge them at least every three months. Disposing of the rechargeable Lithium-ion battery Discharge the Lithium-ion battery before disposing of it. When disposing of the battery, be sure to do so in an environmentally sensitive manner. Adhere to any local and national regulations concerning battery disposal or recycling. 48. 2 Operating with the controller If the receiver is being powered by its internal batteries, it does not supply power to the controller when they are connected. The receiver and the Trimble controller must be charged using their own power supplies with connections to the AC power supply from the wall. 48. 3 Power output If the receiver is being supplied with power from an external source, power is automatically output on Port 1. Port 1 outputs a maximum voltage of 20 V, even if the input voltage is higher. You can use GPS Configurator or Trimble Survey Controller software to enable power output on Port 3. Port 3 can be enabled for power output regardless of whether power is supplied internally or externally. On Port 3, the output voltage is approximately 0. 5 V less than the input voltage. For example, if power is being supplied from the internal Lithium-ion batteries, the maximum battery voltage is 8. 4 V, so the maximum output voltage is 7. 9 V. Note ­ When you start a survey using the Trimble Survey Controller software, and you are using an external radio, the software automatically enables power output on Port 3. 48. 4 Firmware A receiver's firmware is the program inside the receiver that makes the receiver run and controls the hardware. You can upgrade the firmware for the receiver using the WinFlash utility provided on the receiver CD. For more information, see The WinFlash utility, page 58. C CAUTION ­ Downgrading the firmware deletes all application files on the receiver. Trimble R7 GNSS and 5700 GPS Receivers User Guide 43 Trimble R7/5700 GPS Receiver Operation Keep all batteries on continuous charge when not in use. Batteries may be kept on charge indefinitely without damage to the receiver or batteries. 4 General Operation 44 Trimble R7 GNSS and 5700 GPS Receivers User Guide CHAPTER 5 Configuration In this chapter: 5 Configuring the receiver in real Time Configuring the receiver using application files Application files The receiver has no controls to change settings. [. . . ] Load the latest version of the firmware, which you can download from www. trimble. com/support The receiver is tracking fewer Wait until the SV Tracking LED is than four satellites. The radio antenna cable and Make sure that the GPS antenna GPS antenna cable are mixed cable (with the yellow over-mould) is connected between the yellow TNC up. connector marked GPS and the GPS antenna. 1 00 Trimble R7 GNSS and 5700 GPS Receivers User Guide Troubleshooting C C. 2 Receiver issues The following table describes some possible receiver issues, possible causes, and how to solve them. Issue Possible cause Solution Check the charge on the external battery, and check the fuse if applicable. Check the charge on the internal batteries and replace if necessary. [. . . ]