User manual TRIMBLE HR150

[. . . ] Magnet--holds the receiver on a wall molding, cross-T, runner, etc. Battery Housing--holds two AA alkaline or Ni-Cd batteries. Battery Door--holds the batteries securely in place. Neck Cord Holder--allows a neck cord to be attached to the receiver. [. . . ] Note: When the receiver is being turned off, all the LEDs and the audio signal quickly turn on for one second. Selecting the Audio Function The receiver always starts up with the audio mode active. Press the power/audio button repeatedly to turn on/off the audio function. Note: If the audio function is on, the receiver beeps quickly when the receiver is above the laser beam, slowly when below it, and continuously when centered in the laser beam or on grade. Press the power/audio button to turn on the receiver. Position the receiver so that its photocell faces the laser. Move the receiver up/down until the LEDs show an on-grade reading. Note: The top/bottom red LEDs flash when the receiver is above or below the laser beam. The green LED flashes when the receiver is on grade. LED/Audio Information LED/Audio Indication Function Green LED: flashes once every two seconds Top red LED: flashing Green LED: flashing Bottom red LED: flashing Both red LEDs: flashing in sequence Receiver is on High On-grade Low Low battery Audio on Beam location Audio Output N/A Fast beeping tone Continuous tone Slow beeping tone N/A 3 beeps Single beep High On Grade Low Power/Audio Button Audio Port Low Battery Speaker beep 1. Release the battery door using your fingers, a coin, or a screwdriver. Install/Remove the 2 AA batteries noting the positive (+) and negative (­) diagram on the bottom of the battery housing. Close the battery door and latch it shut. ­5­ ­6­ ­7­ ­8­ General-Purpose Clamp The C61 general-purpose clamp allows the receiver to be attached to a survey rod or wooden pole. Features and Functions 1 2 3 4 Attaching the Receiver to the Survey Rod or Wooden Pole 1. Slide the general purpose clamp into the receiver until it "clicks" into position. Turn the jaws screw counterclockwise to open the clamp's jaws. Slide the survey rod or wooden pole between the clamp's jaws. Turn the jaws screw clockwise to hold the general-purpose clamp securely in place. Receiver Specifications LED Channels Capture Height Acceptance Angle On-Grade Sensitivity Power Source Low Battery Indicator Automatic Shutoff Spectral Sensitivity 3 50 mm (2 in. ) 90° Medium: 3. 00 mm (1/8 in. ) Two 1. 5-V batteries (type LR6/AA) Red LEDs flash in sequence 30 minutes after last laser detection or push-button actuation Operates with red visible and infrared rotating lasers with wavelength between 610 and 900 nm 50 mm (2 in. ) below top of receiver, on both sides ­20 °C to +50 °C (­4 °F to +122 °F) ­40 °C to +70 °C (­40 °F to +158 °F) 0. 3 kg (. 75 lb) 13. 6 x 5. 0 x 2. 8 cm (5. 37 x 2. 00 x 1. 11 in. ) ­ 11 ­ Notice to Our European Union Customers For product recycling instructions and more information, please go to: www. trimble. com/environment/summary. html Recycling in Europe To recycle Trimble WEEE, call: +31 497 53 2430, and ask for the "WEEE associate, " or mail a request for recycling instructions to: Trimble Europe BV c/o Menlo Worldwide Logistics Meerheide 45 5521 DZ Eersel, NL Battery Life @ 20 °C (68 °F) Alkaline: 70+ hours 5 Marking Notch 1. Release Tab--allows the receiver to be locked onto or released from the general-purpose clamp. Jaws--close/open so that the general-purpose clamp can be attached to or released from a survey rod or wooden pole. Reading Edge--aligns with the receiver's on-grade marking notches. Jaws Screw--controls the closing/opening of the jaws. Circular Bubble Screw Holes--are where the optional 1277-6251S grade rod circular bubble kit is mounted. ­9­ ­ 10 ­ Operating Temperature Storage Temperature Weight Dimensions (H x W x D) ­ 12 ­ EMC Declaration of Conformity This receiver has been tested and found to comply with the limits for a Class B digital device for radio noise for digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communication, and is pursuant to part 15 of the Federal Communication Commission (FCC) rules. [. . . ] Customers should send the product to Trimble Navigation Ltd. or the nearest authorized service center for warranty repairs, freight prepaid. In countries with Trimble subsidiary service centers, the repaired product will be returned to the customer, freight prepaid. Any evidence of negligent, abnormal use, accident, or any attempt to repair the product by other than factory-authorized personnel using Trimble certified or recommended parts, automatically voids the warranty. [. . . ]