User manual TRIMBLE TERRASYNC 2.11 RELEASE NOTES REV A

[. . . ] TerraSyncTM Release Notes Version 2. 11 June 2002 Revision A Trimble Navigation Limited Mapping & GIS Division 645 North Mary Avenue Post Office Box 3642 Sunnyvale, CA 94085 U. S. A. Phone: +1-408-481-8940 1-800-545-7762 Fax: +1-408-481-7744 www. trimble. com Legal Information Revision Notice This is the June 2002 release (Revision A) of the TerraSync Release Notes. It applies to version 2. 11 of the TerraSyncTM software. Copyright © 2000­2002 Trimble Navigation Limited. For STL support, the TerraSync software uses the Moscow Center for SPARC Technology adaptation of the SGI Standard Template Library. © 1994 Hewlett-Packard Company, © 1996, 97 Silicon Graphics Computer Systems, Inc. , © 1997 Moscow Center for SPARC Technology. [. . . ] Then start the installation again. More. . . TerraSync Release Notes Installation on a CE Device 26 If memory space in the secondary internal storage location is insufficient, the installation may appear to complete successfully, but error messages may appear when you try to run the TerraSync software. If this happens, make more space available in the secondary storage location, then install the software again. If the problem persists, perform a full hard reset of the CE device. For information on performing a full hard reset, refer to the Trimble website. Then reinstall the TerraSync software. NOTE Trimble recommends that you uninstall any previously installed versions of the TerraSync software and transfer any TerraSync data files to your office computer before installing the latest version. Connect the CE device to the office computer. You can use any of the following methods: · · serial cable infrared · · cradle modem · · USB network card For information on connecting your CE device to another computer, refer to the documentation for your CE device. Make sure that the CE device and computer are switched on. If an ActiveSync partnership for these two computers exists, ActiveSync starts and the office computer connects to the CE device automatically. More. . . TerraSync Release Notes Installation on a CE Device 27 NOTE ActiveSync cannot connect to a CE device that is communicating with a GPS receiver on the same port. If you are upgrading or reinstalling the TerraSync software, make sure you disconnect from GPS and exit the software. If there is no partnership, or the computers do not connect, you may need to install or set up ActiveSync on your office computer. For more information, refer to the documentation for your CE device. When the two computers are connected, the Microsoft ActiveSync window appears and displays the message Connected: More. . . TerraSync Release Notes Installation on a CE Device 28 TIP If ActiveSync is installed, but the two computers do not connect, check that the CE device is set up to establish a PC connection. Open the Communications Properties dialog on your CE device. For information on how to do this, refer to the documentation for your CE device. Select the PC Connection tab and check that the Allow connection with desktop computer when device is attached check box is selected. You should also ensure that the CE device is configured to connect at the maximum baud rate available. TIP 3. Make sure the TerraSync software is not running on the CE device. More. . . TerraSync Release Notes Installation on a CE Device 29 4. Insert the TerraSync CD-ROM in the CD drive of your office computer. If this screen does not appear, select autorun. exe from your CD drive folder. More. . . TerraSync Release Notes Installation on a CE Device 30 6. If necessary, select Change Language, then select the language you want to install the software in. [. . . ] Then connect as for a standard COM port. More. . . TerraSync Release Notes Cabling 51 WARNING Using COM port cabling that supplies power to the CE device can cause problems with, or even permanent damage to, the CE device. Some GPS receivers supply power, and some cables transfer power through one or more of their pins. Trimble strongly recommends that you protect your CE device by connecting either the null modem adapter (P/N 43197) or the curly straight-through cable (P/N 45052) to the receiver cable. These two connectors do not supply power, so they will protect your CE device from power output by the receiver. If a powered connection is acceptable or necessary, you can connect directly to the receiver, or you can use the curly straight-through cable P/N 30236 instead of cable P/N 45052. [. . . ]