User manual TYAN THUNDER I7500

[. . . ] Thunder i7500 /// Revision 2. 01 S2720 Copyright © TYAN Computer Corporation, 2001-2002. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Thunder i7500 S2720 are trademarks of TYAN Computer Corporation. [. . . ] Quick Boot Quiet Boot Add-On Rom Display Mode Boot up Num-Lock Boot up CPU Speed PS/2 Mouse Support Typematic Rate System Keyboard Enabled Disabled Enabled Disabled Force BIOS Keep Current On Off High Low Enabled Disabled Fast Slow Present Unavailable Enabled Disabled Enabled Disabled Enabled Disabled When set to Enabled, some self-tests will be skipped during POST. If set to Enabled, OEM logo will be displayed instead of POST messages. This setting toggles the Add-On ROM video display mode. Specifies whether Num-Lock will be on or off during bootup. Will allow continual boot even if the keyboard is not attached. Toggles checking of system memory for corruption. If Enabled, you will have to press F1 for the system to continue booting if an error is detected during POST. Toggles display of pressing DEL key to enter BIOS. Parity Check Wait for F1 if "error" Hit "Del" Message 28 http://www. TYAN. com 3. 6 ­ Super IO Configuration Options related to the IO interface can be altered through the following. Serial Port 1, 2 Address Onboard CIR Port Parallel Port Address Enabled Disabled Auto Enabled Disabled 3F8, 2F8 3E8, 2E8 Output Only Bi-directional EPP ECP Toggles use of serial ports 1 and or 2. Enabling ports also requires you to enter the I/O address for that port unless you select Auto. These options are dependent on the IRQ and vice versa. Standard one-way protocol for parallel devices. Two-way protocol Enhanced Parallel Port may provide higher bandwidth if an EPP compliant device is used (e. g. Enhanced Compatibility Port may provide higher bandwidth if an ECP compliant device is used (e. g. These options appear when the parallel port is set to Enabled. Parallel Port Mode Parallel Address 378 278 3BC 3. 7 ­ Onboard Device Configuration Options related to onboard devices can be altered through the following. Onboard ATI RageXL Video Onboard 82550 Onboard 82544GC Onboard SCSI Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Toggles the onboard ATI video graphics. Toggles the onboard SCSI controller. 3. 8­ USB Configuration Options related to USB can be altered through the following. USB Function Legacy USB Support Enabled Disabled Enabled Disabled Auto Enabled Disabled Auto Enabled Disabled Toggles the onboard USB ports. Toggles the use of onboard USB ports in DOS. USB Zip Emulation Type USB Beep Message Toggles Zip drive emulation on USB ports when in use. Toggles USB beep error messaging. 29 http://www. TYAN. com 3. 9 ­ PCIPnP Options related to the Plug and Play PCI settings interface can be altered through the following. Yes No Yes No 32, 64, 96, 128, 160, 192, 224, 248 Yes No Enabled Disabled Toggles the option of letting the OS take care of IRQ routing or the BIOS. Select Yes to let the OS manage IRQ settings. [. . . ] PCI card that allows a RAID card to use the onboard SCSI chip, thus lowering cost of RAID solution ZIF Socket (Zero Insertion Force socket): these sockets make it possible to insert CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shift the processor over and down, guiding into the board and locking it into place. 41 http://www. TYAN. com Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. [. . . ]