User manual TYAN THUNDER K8SE

[. . . ] Thunder K8SE /// Version 1. 02 S2892 Copyright Copyright © TYAN Computer Corporation, 2004-2005. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Taro and Thunder K8SE are trademarks of TYAN Computer Corporation. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. [. . . ] Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced I/O Device Configuration Serial port A: Serial port B: Mode: Parallel port: Mode: Floppy disk controller: Base I/O address: [Auto] [Auto] [Normal] [Auto] [ECP] [Enabled] [Primary] Item Specific Help F1: Help õ¡ô : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit ¡ö ¡÷ : Select Menu Enter: Select Sub-Menu F10: Save and Exit Feature Serial port A/B Mode Parallel port Mode Floppy disk controller Base I/O address Option Auto Enabled Disabled Normal IR IRQ4 Auto Enabled Disabled ECP EPP Output only Bi-directional Enabled Disabled Primary Secondary 50 Description Configure serial port A/B using options. Set the mode for Serial port B using options. Set the mode for parallel port using options. Configure Floppy disk controller using options. Set the base I/O address for parallel port. http://www. tyan. com 3. 6. 7 ­ Hardware Monitor Sub-Menu You can use this screen to select options for the Hardware Monitor settings. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Hardware Monitor CPU 1 Temperature CPU 1 local Temperature CPU 2 local Temperature System Temperature 1 System Temperature 2 Fan Control and Monitor System Voltage Monitor Item Specific Help F1: Help õ¡ô : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit ¡ö ¡÷ : Select Menu Enter: Select Sub-Menu F10: Save and Exit Feature Fan Control and Monitor System Voltage Monitor Option Menu Menu Description Monitor and control the system fan. View the system voltage value 51 http://www. tyan. com Fan Control and Monitor You can use this screen to select options for the Hardware Monitor settings. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Fan Control and Monitor Auto FAN Power Control CPU 1 Fan Speed CPU 2 Fan Speed System Fan1 Speed System Fan2 Speed System Fan3 Speed System Fan4 Speed [Disabled] Item Specific Help F1: Help õ¡ô : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit ¡ö ¡÷ : Select Menu Enter: Select Sub-Menu F10: Save and Exit Feature Auto FAN Power Control Option Disabled Enabled Description Configure FAN power duty cycle control. 52 http://www. tyan. com System Voltage Monitor All items on this menu are shown only which cannot be modified. PhoenixBIOS Setup Utility Advanced Fan Control and Monitor CPU 1 Vcore (V) +3. 3V VBat (V) H1 DDR VTT 1. 3V H1 DDR 2. 5V VDD HT0 RUN VDD 3. 3V 5V 12V Item Specific Help F1: Help õ¡ô : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit ¡ö ¡÷ : Select Menu Enter: Select Sub-Menu F10: Save and Exit 53 http://www. tyan. com 3. 6. 8 ­ Console Redirection Sub-Menu You can use this screen to select options for the Console Redirection settings. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Console Redirection Com Port Address Baud Rate Console Type Flow Control Console connection Continue C. R. after POST [Disabled] [19. 2K] [PC ANSL] [CTS/RTS] [Direct] [off] Item Specific Help F1: Help õ¡ô : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit ¡ö ¡÷ : Select Menu Enter: Select Sub-Menu F10: Save and Exit Feature Com Port Address Baud Rate Console Type Option Disabled Onboard COMA Onboard COMB 19. 2K 300 1200 2400 9600 38. 4K 57. 6K PC ANSL VT100 VT100 8bit VT100+ 54 Description Select the Com Port address. Enable the specified baud rate. Enable the specified console type. http://www. tyan. com Flow Control PC-ANSI 7bit VT-UTF8 CTS/RTS XON/XOFF None Direct Enable flow control. Indicate whether the console is connected directly to the system or a modem is used to connect. Enable Console Redirection after OS has loaded. Console connection Via modem Continue C. R. after POST Off On 3. 7 - BIOS Memory Menu This menu has options for memory speed & latency. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. Main Advanced PhoenixBIOS Setup Utility Memory Security Boot [XXXX KB] [XXXX KB] [Enabled] [Write Back] [Write Back] [Write Back] [Write Back] [Write Back] [Write Back] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] Power Exit Cache Ram System Memory: Extended Memory: Memory Cache: Cache System BIOS area: Cache Video BIOS area: Cache Base 0-512k: Cache Base 512k-640k: Cache Extended Memory Area: Cache A000 ­ AFFF: Cache B000 ­ BFFF Cache C800 ­ CBFF: Cache CC00 ­ CFFF: Cache D000 ­ D3FF: Cache D400 ­ D7FF: Item Specific Help F1: Help õ¡ô : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit ¡ö ¡÷ : Select Menu Enter: Select Sub-Menu F10: Save and Exit 55 http://www. tyan. com Feature Memory Cache Cache System BIOS area Cache Video BIOS area Cache Base 0-512k Cache Base 512k-640k Cache Extended Memory Area Option Enabled Disabled Write Back Write Through Write Protect uncached Write Back Write Through Write Protect uncached Write Back Write Through Write Protect uncached Write Back Write Through Write Protect uncached Write Back Write Through Write Protect uncached Disabled USHC Write Through Write Protect Write Back Description Set the state of memory cache. Control caching of system BIOS area. Control caching of video BIOS area. Control caching of 512k base memory. Control caching of 512k 640k base memory. Control caching of system memory above one megabyte. Cache A000-AFFF Cache D400-D7FF Control caching of the memory blocks. 56 http://www. tyan. com 3. 8 - Security Menu This menu has options for the Security options. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. Main Advanced PhoenixBIOS Setup Utility Memory Security Boot Power Exit Supervisor Password Is: User Password Is: Set Supervisor Password Set User Password Password on boot: Fixed disk boot sector: Diskette access: [Enter] [Enter] [Disabled] [Normal] [Supervisor] Item Specific Help F1: Help õ¡ô : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit ¡ö ¡÷ : Select Menu Enter: Select Sub-Menu F10: Save and Exit Feature Password on boot Fixed disk boot sector Diskette access Option Disabled Enabled Normal Write Protect User Supervisor Description Enable password entry on boot. Write protects boot sector on hard disk to protect against viruses. [. . . ] With all these convenient resources just a few keystrokes away, users can easily find the latest software and operating system components to keep their systems running as powerful and productive as possible. Tyan also ranks high for its commitment to fast and friendly customer support through email. By offering plenty of options for users, Tyan serves multiple market segments with the industry's most competitive services to support them. "Tyan's tech support is some of the most impressive we've seen, with great response time and exceptional organization in general" Anandtech. com Please feel free to contact us directly for this service at techsupport@tyan. com Help Resources: 1. [. . . ]