User manual TYAN THUNDER K8SRE

[. . . ] Thunder K8SRE /// Version 1. 0 S2891 Copyright Copyright © TYAN Computer Corporation, 2004-2005. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Taro and Thunder K8SRE are trademarks of TYAN Computer Corporation. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. [. . . ] Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Legacy Diskette A: Legacy Diskette B: [Disabled] [Disabled] Item Specific Help Indicates a DMA, interrupt, I/O, or memory resource conflict with another device. F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Legacy Diskette A/B Option Disabled Enabled Description Select floppy type 48 http://www. tyan. com 3. 6. 6 - I/O Device Configuration Sub-Menu You can use this screen to select options for the I/O Device Configuration settings. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Serial port A: Base I/O address: Interrupt: Serial port B: Mode: Base I/O address: Interrupt Parallel port: Base I/O address: Interrupt: Mode: DMA channel: Floppy disk controller: Base I/O address [Disabled] [3F8] [IRQ 3] [Disabled] [Normal] [3F8] [IRQ3] [Disabled] [378] [IRQ5] [Output only] [DMA1] [Disabled] [Primary] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values Feature Serial port A Base I/O address Interrupt Serial port B Mode Base I/O address Option Disabled Enabled 3F8 2F8 IRQ3 IRQ4 Disabled Enabled Normal IR 3F8 2F8 49 Description Configure serial port A using options. Set the base I/O address for serial port A. Set the mode for Serial port B using options. Set the base I/O address for serial port B. http://www. tyan. com Interrupt Parallel port Base I/O Address Interrupt Mode DMA channel Floppy disk controller Base I/O address IRQ3 IRQ4 Disabled Enabled 378 278 IRQ5 IRQ7 Output only Bi-directional DMA 1 DMA 3 Disabled Enabled Primary Secondary Set the interrupt for serial port B Configure parallel port using options. Set the base I/O address for parallel port. Set the mode for parallel port using options. Configure Floppy disk controller using options. Set the base I/O address for parallel port. 3. 6. 7 ­ Console Redirection Sub-Menu You can use this screen to select options for the Console Redirection settings. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Com Port Address Baud Rate Console Type Flow Control Console connection Continue C. R. after POST [Disabled] [300] [VT100] [None] [Direct] [off] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values 50 http://www. tyan. com Feature Com Port Address Baud Rate Console Type Flow Control Option Disabled On-board COMA On-board COMB 300 1200 VT100 VT100, 8bit None XON/XOFF Direct Description Select the Com Port address. Indicate whether the console is connected directly to the system or a modem is used to connect. Enable Console Redirection after OS has loaded. Console connection Via modem Continue C. R. after POST Off On 51 http://www. tyan. com 3. 7 - BIOS Memory Menu This menu has options for memory speed & latency. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Memory Cache Ram System Memory: Extended Memory: Memory Cache: Cache System BIOS area: Cache Video BIOS area: Cache Base 0-512k: Cache Base 512k-640k: Cache Extended Memory Area: Cache A000 ­ AFFF: Cache B000 ­ BFFF Cache C800 ­ CBFF: Cache CC00 ­ CFFF: Cache D000 ­ D3FF: Cache D400 ­ D7FF: Cache D800 ­ DBFF: Cache DC00 ­ DFFF: Cache E000 ­ E3FF: Cache E400 ­ E7FF: Cache E800 ­ E8FF: Cache EC00 ­ EFFF: [XXXX KB] [XXXX KB] [Enabled] [uncached] [uncached] [uncached] [uncached] [uncached] [uncached] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values 52 http://www. tyan. com Feature Memory Cache Option Disabled Enabled Disabled USHC Write Through Write Protect Write Back Disabled Write Through Write Protect Write Back Description Set the state of memory cache. Cache A000-AFFF Cache B000-BFFF Control caching of the memory blocks. Cache C800-CBFF ~ Cache EC00-EFFF Control caching of the memory blocks. 3. 8 - Security Menu This menu has options for the Security options. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Boot Supervisor Password Is: User Password Is: Set Supervisor Password Set User Password Password on boot: Fixed disk boot sector: Diskette access: Virus check reminder: System backup reminder: [Disabled] [Normal] [User] [Disabled] [Disabled] Item Specific Help F1: Help : Select Item -/+: Change Values F9: Setup Defaults Esc: Exit : Select Screen Enter: Select Sub-Menu F10: Previous Values 53 http://www. tyan. com Feature Password on boot Fixed disk boot sector Diskette access Option Disabled Enabled Normal Write Protect User Supervisor Disabled Virus check reminder Daily Disabled System back reminder Daily Description Enable password entry on boot. Write protects boot sector on hard disk to protect against viruses. Display reminder message at boot (daily, every Monday or 1st of every month). [. . . ] ZCR (Zero Channel RAID): PCI card that allows a RAID card to use the onboard SCSI chip, thus lowering cost of RAID solution ZIF Socket (Zero Insertion Force socket): these sockets make it possible to insert CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shifts the processor over and down, guiding it into the board and locking it into place. 68 http://www. tyan. com Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. [. . . ]