User manual TYAN THUNDER N4250QE

[. . . ] Thunder n4250QE /// Version 1. 00 S4985G3NR Copyright Copyright © TYAN Computer Corporation, 2006. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Thunder n4250QE are trademarks of TYAN Computer Corporation. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. [. . . ] Ultra DMA (UDMA, or, more accurately, Ultra DMA/33) is a protocol for transferring data between a hard disk drive through the computer's data paths (or bus) to the computer's random access memory (RAM). The Ultra DMA/33 protocol transfers data in burst mode at a rate of 33. 3 MBps (megabytes per second), twice as fast as the previous Direct Memory Access (DMA) interface. Ultra DMA support in your computer means that it will boot (start) and open new applications more quickly. It will also help users of graphics-intensive and other applications that require large amounts of access to data on the hard drive. Ultra DMA uses Cyclical Redundancy Checking (CRC), offering a new level of data protection. Disabled / Mode 0 / Mode 1 / Mode 2 / Mode 3 / Mode 4 / Mode 5 52 3. 3. 6 Floppy Configuration You can use this screen to select options for the Floppy Configuration settings. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. PhoenixBIOS Setup Utility Advanced Memory Security Boot Power Exit Floppy Configuration Item Specific Help Main Large Diskette A: [1. 44/1. 25 MB 3 I F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Legacy Diskette A This feature allows you to select the floppy type. Disabled / 360kb 5 1/4" / 1. 2MB 5 1/4" / 720kb 3 1/2" / 2. 88MB 3 1/2" 53 3. 3. 7 I/O Device Configuration This setting allows you to configure I/O devices. PhoenixBIOS Setup Utility Advanced Memory Security Boot Power Exit I/O Device Configuration Item Specific Help [Enabled] [3F8] [IRQ4] [Enabled] [Normal] [2F8] [IRQ3] [Auto] [ECP] [Enabled] [Primary] Main Serial port A: Base I/O address: Interrupt: Serial port B: Mode: Base I/O address Interrupt: Parallel port: Mode: Floppy Disk Controller: Base I/O address: F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Serial Port A This defines how the serial port is detected and configured. Enabled / Disabled / Auto Base I/O Address This sets the base I/O address for serial port A. 3F8 / 2F8 / 3E8 / 2E8 Interrupt This sets the interrupt for serial port A. IRQ4 / IRQ3 Serial Port B This defines how the serial port is detected and configured. Enabled / Disabled / Auto Mode This feature is used to set the mode for serial port B. Normal / IR / ASK-IR 54 Base I/O Address This sets the base I/O address for serial port B. 2F8 / 3F8 / 3E8 / 2E8 Interrupt This sets the interrupt for serial port B. IRQ3 / IRQ4 Parallel port: This defines how the parallel port is detected and configured. Auto / Disable / Enabled Mode This feature is used to set the mode for parallel port. ECP / Output Only / Bi-directional / EPP Floppy Disk Controller This defines how the floppy disk controller is detected and configured. Enabled/ Disabled / Auto Base I/O Address This sets the base I/O address for floppy disk controller. Primary / Secondary 55 3. 3. 8 Hardware Monitor This displays critical system parameters like CPU speed, fan speeds, voltage levels and CPU temperature. PhoenixBIOS Setup Utility Memory Security Boot Power Exit Hardwar Monitor Item Specific Help Main Advanced CPU0 Temperature CPU1 Temperature CPU2 Temperature CPU3 Temperature Sys1 Temperature Sys2 Temperature Sys3 Temperature Sys4 Temperature Sys5 Temperature CPU0 Fan Speed CPU1 Fan Speed CPU2 Fan Speed CPU3 Fan Speed System Fan0 Speed System Fan1 Speed System Fan2 Speed System Fan3 Speed System Fan4 Speed System Fan5 Speed System Fan6 Speed System Fan7 Speed CPU0 VDD voltage CPU1 VDD voltage +12V +5V HT1. 2V 3. 3VSB CK804 Vcore 1. 5V F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values 56 3. 3. 9 Console Redirection Main PhoenixBIOS Setup Utility Advanced Memory Security Boot Power Exit Console Redirection Item Specific Help [Disabled] [19. 2K] [PC ANSI] [CTS/RTS] [Direct] [Off] Com Port Address Baud Rate Console Type Flow Control Console connection: Continue C. R. after POST: F1 Help Esc Exit ¡ö ¡ô õ ¡÷ Select Item Select Menu -/+ Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Previous Values Com Port Address If enabled it will use a port on the motherboard. Disabled / On-board COM A / On-board COM B Baud Rate This feature is used to enable the specified baud rate. [. . . ] PCI card that allows a RAID card to use the onboard SCSI chip, thus lowering cost of RAID solution ZIF Socket (Zero Insertion Force socket): these sockets make it possible to insert CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shift the processor over and down, guiding into the board and locking it into place. 81 Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. [. . . ]