User manual U-LINE BI2115SSHL

[. . . ] Use and Care Guide Ice Maker Model: BI2115 BI2115 1 Introduction Congratulations on your purchase of a U-Line refrigeration product. A pioneer in the field for more than 40 years, U-Line Corporation is the world's number one manufacturer of built-in, under-counter, specialty refrigeration and ice making products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology consistently leads the market with innovation, design, depth of product line and performance. [. . . ] Clean the interior and all removed components using a mild non-abrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. Rinse the interior using a soft sponge and clean water. · Do not use any solvent-based or abrasive cleaners. These types of cleaners may transmit taste to the interior products and damage or discolor the interior. Figure 5 ULIN_0188_A BI2115 9 To defrost: 1. Place a towel or other absorbent material on bottom of unit (Figure 5, 1). If you would like, place warm water inside ice bucket. Then place ice bucket back into unit and close door. After approximately one hour, remove ice bucket and discard water. Allow the frost to completely melt naturally. Clean the interior and ice bucket using a mild non-abrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. NOTE: DO NOT use any solvent-based or abrasive cleaners. They will discolor or damage the interior. Dampen a soft sponge or non-abrasive cloth in clean water and wipe down the cabinet interior and ice bucket to remove any detergent residue. Rinse the sponge or cloth in clean water and repeat as necessary until the cabinet and ice bucket are clean. 2. Loosen two screws (Figure 6, 1) completely. NOTE: Screws are held in the grille by o-ring retainers, and will not come free of the grille. Remove the grille. WARNING DO NOT touch the condenser fins. The condenser fins are SHARP and can be easily damaged. CAUTION DO NOT use any type of cleaner on the condenser unit. Clean the condenser coil (Figure 6, 2) using a soft brush with a "combing" action or vacuum cleaner. Position the grille to align the mounting screws with the holes in the cabinet. Secure, but do not over-tighten both grille screws. [. . . ] Set cube size smaller (See MAINTENANCE; ICE MAKER; ICE CUBE THICKNESS ADJUSTMENT). BI2115 15 This page intentionally left blank 16 BI2115 This page intentionally left blank BI2115 17 This page intentionally left blank 18 BI2115 U-Line Corporation Limited Warranty U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year warranty period for all U-Line products U-Line shall: (1) at U-Lines option, repair any product or replace any part of a product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part. During years two through five of the warranty period for the sealed system, ULine shall: (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. All other charges, including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty, shall be borne by you. [. . . ]