User manual UFREE SCOOTER SCOOTER ELETTRICO FS-E11

[. . . ] 1. 1. 2 To ensure this scooter to have a long life, please read the manual instructions before your operation to this scooter. Don't lend it to the people who can't operate this scooter correctly. 1. 1. 3 Since the speed is fast, please be careful to use it in the snow or rain weather, have a brake in advance when braking is necessary. 1. 1. 4 Without adult's supervision, minors mustn't operate this scooter. [. . . ] 1. 4. 2 To ensure the battery to be in good condition, please charge it in time after your riding. 1. 4. 3 Should not start up the scooter frequently on the grade road. Frame and instruction 2. 1 This scooter is equipped with the battery of high power and lead-acid free of maintenance. The battery is located in the best place, make the gravity point low, and insure the balance & safety to the rider. 2. 2 This scooter is equipped with the electric driving control non-grade HUOER accelerator system, which can protect the motor and battery effectively and have a safety operation. 2 UFREE SCOOTER www. scooter-manufacturer. com 2. 3 One special full automatic charger is used to this scooter, which can avoid overcharge. Main technical parameter and function index 3. 1 Entire scooter specification: Max speed: 12. 5 miles/hour Range per charge: 10 miles Max load: 200 lbs Incline capacity: approx. 4° Net weight including battery: 45 lbs Tyre: 12" pneumatic 3. 2 Motor parameter: Rated power: 250W-350W Rated volt: 24V 3. 3 Battery: Type: high power lead-acid storage battery free of maintenance Current: 12AH Voltage: 12Vx2 3. 4 Charger: Input volt: 110-220V Charge time: 6-8H 4. 4. 1 Assemble and adjust method Assemble 4. 1. 1 Take out the scooter from the carton. (Figure 1) 4. 1. 2 Loose the flat bolt in the handle bar, remove the pin and insert the connector to handle bar, then insert the pin shaft, tighten the bolt, turn and tighten the folding unit to steady the handle. (Figure 2) 3 UFREE SCOOTER www. scooter-manufacturer. com Assemble the handle bar, put the accelerator correct location, fix it with hex spanner. (Figure 3) 4. 2 Assemble the saddle pipe, adjust and tighten. (Figure 4) 4. 3 Adjust the rear brake 4. 3. 1 Adjust the rear adjusting bolt, tighten the brake bar to insure rear wheel not turning, loose the brake bar, rear wheel turning freely. (Figure 5) 4. 3. 2 If brake shoe (brake rubber) wear-tear too much, please replace it in time. 4. 4 Front wheel assembly, maintenance and service. 4. 4. 1 Loose the front shaft nut, remove the special washer to the hole (O6. 5), tighten front shaft nut, insure the front wheel in correct location. (Figure 6) 4. 5 Adjust the chain 4. 5. 1 Loose the rear shaft nut. 4. 5. 2 Loose the bolts on both sides, move the rear wheel backside, adjust and make the chain running freely, tighten rear shaft nut. (Figure 7) 4. 6 Assembly the rear wheel 4. 6. 1 Loose the rear shaft nut, put off the chain, take out the rear wheel. [. . . ] The type is short of of the requirement 2. Many ascents, low heavy wind, the road surface isn't weight is over 200 Over many brake 4 The charger can't be 1. The lead of the 5 No displaying of the 1. Start the electric charging state of the see if the battery and the electric than 20. 5V; can't start. [. . . ]