User manual ULINE ECHELON CLR2060

[. . . ] É c h e l o nTM U S E R M A N U A L U-LINE CORPORATION LIMITED WARRANTY U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year warranty period for all U-Line products U-Line shall: (1) at U-Line's option, repair any product or replace any part of a product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part. During years two through five of the warranty period for the sealed system, U-Line shall:. (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. [. . . ] Tilt top of door into position in top hinge and install top hinge screw pin. Install plastic screw plugs removed in Step 2 in old hinge holes (3 each, top and bottom). UL312A 8. 9. Figure 18 16 CUSTOM DOOR PANELS Two types of custom door panels can be installed on your U-Line unit to harmonize with or accent the surrounding decor. FULL OVERLAY DOOR PANEL A full overlay door panel completely covers the door frame and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit which contains the Panel Preparation Document for building and installing a full overlay panel. See Table 1 and Figure 19 for full overlay door panel dimensions. Table 1. Full Overlay Panel Dimensions Model CLR2060 A 29-7/8" B 14-3/4" B CUSTOM INSERT DOOR PANEL A custom door panel can be inserted into the door frame to better match the surrounding decor. Custom door panels can be flat or raised, as long as the maximum panel thickness where inserted into the door reveal (channel) is 1/4" thick. For raised A panels, the depth of the reveal is 1/4" on all four sides. See Table 2 and Figure 19 for custom door panel insert dimensions. Table 2. Custom Insert Door Panel Dimensions Model 2015 Series 2075 Series A 28-5/32" 28-5/32" B 14-1/32" 23-1/32" Figure 19 The door panel insert must not weigh more than 20 lbs. 17 User's Manual Install the insert as follows: !Remove top hinge screw pin (7/64" Allen wrench, see Figure 20). Remove door by tilting forward and lifting off bottom hinge pin. Remove two outside screws holding door handle. Slightly separate door handle from door (see Figure 21). Pull door gasket out of groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see Figure 22). Do not remove the three screws behind gasket. Slide custom door panel insert into 1/4 inch channel in door front. Holding door gasket out of the way, replace handle on door making sure it is seated properly on insert and that screw holes line up. Install two small screws removed in step 2. Starting at the corners and working inward, push door gasket into place on door. Place door on bottom hinge pin and install upper hinge screw. 8. UL117 9. BUILT-IN INSTALLATION Your U-Line product has been designed for either free-standing or builtin installation. [. . . ] Check for blown fuse or tripped circuit breaker. Make sure cycle selector switch is set to ICE. Surrounding air temperature must be at least 50°F (10°C). Check to see that water is connected and turned on to the unit. [. . . ]