User manual ULINE ORIGINS 75BEV

[. . . ] User's Manual ICE-MAKERS, COMBOS, REFRIGERATORS, 75 BEV BEVERAGE CENTER U-LINE CORPORATION LIMITED WARRANTY U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year warranty period for all U-Line products U-Line shall: (1) at U-Line's option, repair any product or replace any part of a product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part. During years two through five of the warranty period for the sealed system, U-Line shall:. (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. [. . . ] Note that there may be a nut behind one or both screws on either side. Install hinge on opposite side, bottom of cabinet (Figure 26). Replace nut on back side where installed. Align hinge outer edge with cabinet before tightening screws. 26 5. UL111 Figure 24 UL112 Figure 26 BUSHING UL113 UL110 Figure 25 6. Figure 27 Relocate plastic spacer/bushing on bottom of door to opposite side, and place door on bottom hinge pin (Figure 27). Clean out bushing hole in door bottom with a screwdriver if needed. Remove plastic hole plug from door handle and relocate on opposite side (Figure 28). 7. 27 User's Manual 8. Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge (Figure 28). HINGE RIGHT SIDE DOOR SWING LEFT SIDE DOOR SWING PLASTIC PLUG HOLE RIGHT SIDE HINGE SCREW INVERT SCREW INVERT HINGE PLASTIC PLUG HOLE UL115 Figure 28 9. Fasten upper hinge to unit plugs in hinge holes, top of (three screws). Be en screws until door is aligned careful not to scratch cabinet (Figure 30). Replace three plastic plugs removed in step 8 into holes on top of unit. Replace screws in holes in bottom of unit, opposite side. Reinstall grille (one screw). NOTE On Combo Model 75A (built-in installations only), changing the door mounting to the left side may interfere with ice bucket removal. See BUILT-IN INSTALLATION section for clearance requirements. Any reference to reversing the door does not apply. To reverse the door mounting on Models Combo 75A and 75R (except Stainless Steel models) perform the following: 1. Remove top hinge from cabinet (four screws) (Figure 23). Remove four plastic plugs in hinge holes, top of cabinet, opposite side (Figure 29). Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge (Figure 28). Do not install hinge on cabinet at this time. Remove bottom hinge from cabinet (four screws) and screws on opposite side of cabinet (Figure 31). Remove pivot screw from bottom hinge, invert screw and reinstall pivot screw in hinge (Figure 28). [. . . ] 75 BEV - Make sure the light switch is in the "OFF" position. See CLEANING AND MAINTENANCE. Light won't go out when door is closed. The unit is not cold enough Door gasket not sealing properly Item(s) interfering with door. Dirty condenser coils 49 User's Manual Problem The unit is not cold enough (cont. ) Possible Cause Airflow to front grille blocked Remedy Airflow must not be obstructed to front grille. [. . . ]