User manual ULINE ORIGINS SP-18

[. . . ] Use and Care Guide Ice Maker Models: BI95, BI98, SP18 BI95 BI98 SP18 1 Introduction Congratulations on your purchase of a U-Line refrigeration product. A pioneer in the field for more than 40 years, U-Line Corporation is the world's number one manufacturer of built-in, under-counter, specialty refrigeration and ice making products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology consistently leads the market with innovation, design, depth of product line and performance. [. . . ] Clean the interior and ice bucket using a mild non-abrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. NOTE: DO NOT use any solvent-based or abrasive cleaners. They will discolor or damage the interior. With a standard blade screwdriver or 1/4" nut driver, remove the grille screw (Figure 8, 1). Remove the grille. WARNING DO NOT touch the condenser fins. The condenser fins are SHARP and can be easily damaged. IMPORTANT DO NOT use any type of cleaner on the condenser unit. Clean the condenser coil using a soft brush with a "combing" action or vacuum cleaner. Place the two hook-hinges (located on the rear bottom side of the grille) on the front lip of the unit base. Swing the grille up into position, aligning the grille and cabinet screw hole. 10 BI95, BI98, SP18 6. Insert the grille screw (Figure 8, 1) and tighten. DO NOT remove the inlet screen from the water solenoid valve. Use a toothbrush to gently clean any sediment from the inlet screen. Re-connect the water supply hose connector (Figure 10, 1) to the water solenoid valve (Figure 10, 2). Open the water main supply valve and check for leaks at the water hose connection. Ensure that the water supply line is not kinked. Place the two hook-hinges (located on the rear bottom side of the grille) on the front lip of the unit base. Swing the grille up into position, aligning the grille and cabinet screw hole. Insert the grille screw (Figure 9, 1) and tighten. Disconnect electrical power to the unit. Shut off the water at the main supply valve. Ice Maker Maintenance Inlet Screen Interval - Every Twelve Months The solenoid valve inlet screen must be cleaned at least once each year as follows: WARNING Disconnect electrical power to the unit before cleaning the solenoid valve. Disconnect electrical power to the unit. Shut off the water at the main supply valve. 1 3. [. . . ] Set cube size smaller (See MAINTENANCE; ICE MAKER; ICE CUBE THICKNESS ADJUST). 16 BI95, BI98, SP18 This page intentionally left blank BI95, BI98, SP18 17 This page intentionally left blank 18 BI95, BI98, SP18 U-Line Corporation Limited Warranty U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year warranty period for all U-Line products U-Line shall: (1) at U-Lines option, repair any product or replace any part of a product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part. During years two through five of the warranty period for the sealed system, ULine shall: (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. All other charges, including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty, shall be borne by you. [. . . ]