User manual UNIDEN 202

[. . . ] IMPORTANT CORDLESS TELEPHONE INFORMATION OPERATING DISTANCE/NOISE INTERFERENCE For optimal performance, your phone's base unit should be installed as follows: Away from electrical appliances such as a microwave oven, TV, personal computer, or another cordless phone. In a HIGH and CENTRAL location with no obstructions nearby. BASIC PROGRAMMING PROGRAMMING 2 Press v or w until "Ring Type" displays. THE HANDSET ID Press "#" to toggle among any one Each handset must have a DIFFERENT 3 the four ring tones. If any two handsets have the same ID number, the entire system will not function properly. [. . . ] Plug the headset into the headset jack on the top of the phone (remove the rubber plug if it is covering the jack). 1 PROGRAMACIÓN DEL CÓDIGO DE SEGURIDAD DEL SISTEMA 1 2 3 4 5 Oprima PRG. Oprima v o w hasta que aparezca "Handset ID". Introduzca un número de identificación de estación de 2 dígitos (cualquier número del 11 al 70). Oprima OFF o PRG para terminar la sesión de programación. 1 vo 2 OprimaCode". w hasta que aparezca "Sec Oprima PRG (Programa) en el nuevo auricular. Oprima "#" 3 programar elpara comenzar a código de seguridad. HANDSET LOW BATTERY INDICATOR When the battery pack needs recharging, the low battery icon will be displayed. You may also notice a reduction in the quality of your cordless handset communications. Return the handset to the charging station as soon as possible, whenever the low battery icon is on. 2 Calls can now be made using the headset. return using the handset without 3 Toheadset, tosimply unplug the headset. a INSTALLING THE BELT CLIP of clip into 1 Place one sidesidethe belt handset. the groove on the of the side of 2 Snap the otherthe otherthe belt clip into the groove on side of the handset. Expansion Handset for 2. 4 GHz Spread Spectrum Multiple-Handset Cordless Telephone EASY TO USE OWNER'S GUIDE SYSTEM REGISTRATION (SECURITY CODE) All handsets must be programmed with the SAME security code (Sec. If you don't remember the system security code, refer to one of the handsets already in-use to obtain the code. INITIAL SETUP Congratulations!You have purchased one of the most sophisticated and versatile cordless telephone systems available. The handset will function as either a one-line or a two-line phone, depending on which base unit you have purchased. Please note that this handset must be connected to a multiple handset system base. Once the handset is programmed with the same Security Code as the base unit, it will immediately function as part of the system. Following are brief instructions to program this handset. For detailed instructions to operate your multiple handset system, please refer to the Owner's Guide included with the system Starter set. PROGRAMMING THE SYSTEM SECURITY CODE INSTALL THE CHARGING CRADLE Connect the AC adapter to the back of the charging cradle and plug into an electric outlet. VIEWING THE SYSTEM SECURITY CODE on a system 1 Press PRG (Program)in-use. handset that is already 1 Press PRG (Program) on the new handset. 2 Press v or w until "Sec Code" displays. Press "#" to 3 security code. begin programming the INSTALL THE HANDSET BATTERY Slide open the battery compartment cover and connect the NiMH battery pack as shown in the illustration below. or w (on of the 2 Press v until "Sec the side displays. handset) Code" Sec Code 123456 4 Using the keypad, enter the 6-digit code. PRG end 5 Press OFF or sessiontoOR the programming press v or w to advance to another programming step. [. . . ] Unauthorized repairs void registration and warranty. Contact seller or manufacturer for details of permissible userperformed routine repairs, and where and how to have other than routine repairs made. Incorrect re-assembly can cause electric shock when the appliance is subsequently used. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. [. . . ]