User manual UNIDEN BC-RH96

[. . . ] Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Mounting the BC-RH96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert the BC-RH96 and insert the bracket knobs to lock the Remote Head in position. Attach the provided Cigarette Lighter Power Cord to the rear power jack marked DC IN 13. 8V. Then plug the adapter end into a dash mounted 1V DC socket. Insert the 3-Conductor Mini-Plug of the supplied ten-foot cable in the REMOTE jack on the back of the scanner. Star Washers & Screws Bracket Knobs BC-RH96 8 5. Route the Remote Cable through the Slotted Guide (3) so it lies flat. Route the Power Cord so it does not interfere with any other wires. Using Hook and Loop Material The rear of the unit, when all connectors and cables are properly routed, is flat. This permits using hook and loop material (not supplied) that has a heavy-duty peel and stick adhesive on one side. This material is generally available from electronic supply stores and hardware stores. Do not apply the tape to the rear until all cables are installed and routed correctly. Do not cover the slotted guide with the tape. 9 Follow the directions supplied with the hook and loop material. Locate a suitable spot on the dash, console, or other area. If you use the Remote Head in another place such as a radio room, using tape lets you quickly mount or remove the Head as desired. Note: The two slots on the front of the Remote Head cannot be used for mounting. These slots are cosmetic features only. BC-RH96 Connections Note: Connect the Remote Cable and route it through the cable channel as shown. Then connect the DC Power Cable and route it through the channel. Always route both cables through the channel. 1 2 DC Power Input Jack 1 DC IN 13. 8V REMOTE 2 3 To Remote Cable Mini-Plug Cable Routing Guides Data Port (for firmware updates) 3 4 4 10 Connecting Cables There are three cables that you can connect to the BCRH96. The DC power cable The Remote Control cable The Data Port cable (not supplied with BC-RH96) diameter and wire it with the center positive using at least 18 gauge wire to an extra fuse block terminal of your vehicle. The Remote Head cannot turn power to the scanner off or on. Therefore, consider connecting the power lead of the scanner to a terminal on your vehicle that is turned off when you turn off the ignition key. Remote Head and Scanner Power To provide power to the Remote Head, insert the barrel of the cigarette lighter adapter into the jack in the back of the unit marked DC IN 13. 8V. Insert the other end in a convenient socket on the dash of your vehicle. To connect a power lead permanently, obtain a barrel connector 5. 5 mm diameter, with a center pin mm 11 Control Cable The ten-foot supplied Control Cable has a stereo miniplug on one end and a scanner serial connector on the other. Insert the mini-plug into the REMOTE jack on the rear of the Remote Head. [. . . ] Other than connecting a GPS, the front and the back cannot be used or connected at the same time when the BC-RH96 is in use. For example, if you connect a 9-pin serial cable to your PC to use the UASD programming software, disconnect the BC-RH96 front cable first. 4 Initialize Memory (Reset) To reset the BC-RH96 to factory default settings, follow the sequence below. Note that once done, there is no undo and all programmed keys are reset. With the unit off, press and hold the following keys and turn on power at the same time: [2], [9] and [HOLD]. You see the reset screen below. [. . . ]