User manual UNIDEN BC92XLT

[. . . ] BC92XLT Paper OM. fm Page 1 Tuesday, August 24, 2004 3:56 PM BC92XLT OWNER'S MANUAL OWNER'S MANUAL BC92XLT Paper OM. fm Page 2 Tuesday, August 24, 2004 3:56 PM Precautions Before you use Precautions this scanner, please read and observe the following. This scanning radio has been manufactured so that it will not tune to the radio frequencies assigned by the FCC for cellular telephone usage. The Electronic Communications Privacy Act of 1986, as amended, makes it a federal crime to intentionally intercept cellular or cordless telephone transmissions or to market this radio when altered to receive them. The installation, possession, or use of this scanning radio in a motor vehicle may be prohibited, regulated, or require a permit in certain states, cities, and/or local jurisdictions. [. . . ] If you want to select another channel, press Func + or Func + before you press E. You can also use the 0-9 key to select the bank. If you entered a frequency that has already been entered elsewhere, the scanner sounds an error tone and displays the channel that was duplicated. If you entered the frequency by mistake, press then enter the correct frequency. To enter the frequency anyway, press E to accept. Scanning the Stored Channels To begin scanning channels, press Scan. The scanner scans through all non-locked channels in the activated banks. (See "Locking Out Channels" on Page 48 and "Turning Channel-Storage Banks On and Off" on Page 47). When the scanner finds a Operation 35 BC92XLT Paper OM. fm Page 36 Tuesday, August 24, 2004 3:56 PM transmission, it stops on it. When the transmission ends, the scanner resumes scanning. Notes: · · If you have not stored frequencies into any channels, the scanner does not scan. If the scanner picks up unwanted partial, or very weak transmissions, turn Squelch clockwise to decrease the scanner's sensitivity to these signals. To listen to a weak or distant station, turn Squelch counterclockwise. To ensure proper scanning, adjust Squelch until the audio mutes. · Manually Selecting a Channel You can continuously monitor a single channel without scanning. This is useful if you hear an emergency broadcast on a channel and do not want to miss any details - even though there might be periods of silence - or if you want to monitor a specific channel. To manually select a channel, press Hold, enter the channel number then press Hold again. Or, during scanning, if the radio stops at a channel you want to listen to, press Hold once. (Repeatedly pressing Hold at this time causes the scanner to step through the channels. ) Press Scan to resume automatic scanning. Operation 36 BC92XLT Paper OM. fm Page 37 Tuesday, August 24, 2004 3:56 PM Special Features SpecialCallTM RF Capture Technology Close Features Your scanner's Close Call feature lets you set the scanner so it detects then displays the frequency of a nearby strong radio transmission. Close Call RF capture works great for finding frequencies at venues such as malls and sporting events. You can set the scanner so Close Call detection works "in the background" while you are scanning other frequencies, turn off normal scanning while Close Call is working, or turn off the Close Call feature and use the scanner normally. You can set the scanner so it alerts you when the Close Call feature detects a frequency. You can also set the frequency band where you want the scanner to look for transmissions. Unlike searching, which requires the scanner to tune to a frequency to check for a transmission, Close Call RF capture directly detects the presence of a strong, nearby signal and instantly tunes to the source's frequency. [. . . ] 21. 3 MHz 3rd IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 kHz Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 mW maximum Built-in Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 mm dia, 8 ohm Dynamic Type Current Drain Squelched . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 mA Full Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]