User manual UNIDEN CXAI5198

[. . . ] CXAI 5198 SERIES OWNER'S MANUAL Contents WELCOME/FEATURES TERMINOLOGY CONTROLS & FUNCTIONS GETTING STARTED Setting up the Phone Installing the Beltclip Optional Headset Installation 2 3 4 6 6 11 12 USING THE SPEED DIAL MEMORY Using the Speed Dial Memory 29 29 CALLER ID Caller ID and Caller ID on Call Waiting (CIDCW) 34 34 THE INTEGRATED ANSWERING DEVICE The Integrated Answering Device Setting Up the Answering Machine Turning the Answering System On/Off Setting Your Outgoing Message (Greeting) Using Your Answering System Remote Operation 38 38 39 41 42 43 48 SETTING UP YOUR PHONE Base Setup Handset Setup 13 13 16 BASICS Using Your Phone Call Waiting Placing a Call on Hold Adjusting the Ringer, and Earpiece and Speaker Volume Muting the Ringer Mute Base Microphone Tone Dialing Switch-over Traveling Out of Range Selecting a Different Channel Conferencing Intercom 19 19 22 22 23 24 25 25 25 26 26 27 ADDITIONAL INFORMATION Note on Power Sources General Information 52 52 54 TROUBLESHOOTING Liquid Damage 55 57 PRECAUTIONS & WARRANTY I. C. NOTICE INDEX REMOTE OPERATION CARD 58 60 61 62 [1] www. uniden. com Welcome Congratulations on your purchase of the Uniden Cordless Telephone System!This is a "Corded/Cordless" Telephone unit. The corded handset (on base) can make/receive calls during power failure. [. . . ] ·The greeting must be more than two seconds long, or it will not be recorded. ·To delete the personal outgoing message, press delete while the message is playing. The system announces "Greeting has been deleted. " T H E I N T E G R AT E D ANSWERING DEVICE www. uniden. com THE INTEGRATED ANSWERING DEVICE [42] Selecting Your Greeting With the phone in standby mode, press greeting. Then press greeting again while the outgoing message is played. This switches between the prerecorded greeting and the personal greeting. After finishing playing back the message, a confirmation tone is heard. Announce only feature The announce only feature plays a pre-recorded outgoing message or your own personal outgoing message, but it will not allow the caller to leave a message. To set announce only, follow the steps on "Setting the Record Time" page 39. If you want to use your own greeting and you want to change your greeting to omit the prompt to leave a message, refer to "Selecting Your Greeting" above. The following message is pre-recorded: "Hello, no one is available to take your call. Please call again. " Using Your Answering System The message counter displays the number of messages stored in memory. If the message LED flashes, then there are new messages waiting for you. The answering system is designed to play your new messages first. After you play all your new messages, you can then play your old messages. T H E I N T E G R AT E D ANSWERING DEVICE [43] THE INTEGRATED ANSWERING DEVICE www. uniden. com Playing your messages (play/stop). 1) With the phone in standby mode, press The system announces the number of new and old messages while the message counter displays only the number of new messages. The time and day that each message was received is announced after the message is played. The message counter will then display the number of current stored messages. 2) When all new messages have been played, you hear a confirmation tone, and the system announces "End of messages. " The system returns to standby. 3) After you have reviewed your new messages, you can play your old messages by pressing (play/stop) again. Once you have listened to a new message, it then becomes an old message. The old messages will be played in the order in which they were received. Repeating a message (play/stop) to review your messages. The number of stored messages is 1) Press announced. (repeat/rewind) after a few seconds of 2) To repeat the current message, press beginning the message. [. . . ] 59 INDEX [61] INDEX www. uniden. com Remote Operation Card CUT CUT REMOTE OPERATION CARD Remote access away from home 1. Call your phone number from a touch-tone phone. During the outgoing message, press 0 and enter your PIN code. The answering system announces the number of messages stored in memory and the voice prompts. [. . . ]