User manual UNIDEN DCX520

[. . . ] · Cordless Handset · Charger · Battery (BT-211AR) (2) ("AA" Rechargeable Ni-MH) (Capacity: 1500 mAH, 1. 2V) · AC Adapter (AD-310) (INPUT: 120V AC 60Hz) (OUTPUT: 9V DC 210 mA) · Beltclip · This Owner's Manual · Other Printed Material Uniden Parts Department at (800) 554-3988 Hours: M-F 8:00 a. m. We can also be reached on the web at www. uniden. com. ­2­ Install the AA Batteries Charge the AA batteries for at least 17-20 hours before completing the installation or using the handset. 1 Press down on the battery cover release and slide the cover down until it comes off. 2 3 Install the batteries supplied with your phone. Securely close the battery compartment cover by sliding it until it snaps into place. "Please Register" appears in the display. 4 Place the handset in the charging cradle with the keypad facing forward. [. . . ] If the contacts become very dirty, use water only, dampen a cloth to clean the charging contacts. Then make sure to go back over the charging contacts with a dry cloth before returning the handset to the charger to charge. Connect the Charger 1 2 Connect the AC adapter to the DC IN 9V jack and to a standard 120V AC wall outlet. Set the charger on a desk or tabletop, and place the handset in the charger with the keypad facing forward. contacts ­4­ 3 Make sure the charge LED illuminates. If the LED does not illuminate, check to see that the AC adapter is plugged in and that the handset makes good contact with the charger charging contacts. · Use only the supplied AD-310 AC adapter. · Place the charger close to the AC outlet so that you can unplug the AC adapter easily. Polarity of the plug Register the Handset YOU NEED TO REGISTER THE DCX520 BEFORE USE. 1 2 3 After placing the batteries in the handset and charging the batteries, remove the handset from the charger and place it in the main base. While registering, "Handset Registering" appears in the display. When the registration is complete, "Registration Complete" appears in the display. If the registration fails, "Registration Failed" appears in the display. · An extra handset can be registered when the main base is in the standby mode. · In some cases you may need to attempt registration a few times. Using the DCX520 with the Integrated Answering Device If the original unit has a built-in answering system, you can check your new messages, skip, repeat, or delete your messages with the DCX520 handset. For more instructions, see the owner's manual supplied with the original unit. ­5­ To To To To To To playback a message skip a message repeat the current message repeat the previous message delete a message stop operation Press Press Press Press Press Press the soft key. end. · If you press end before the answering system answers, the phone will return to the standby mode. · When the answering system does not answer within 6 seconds, you will hear a beep and the phone will return to the standby mode. · When you receive a call, the remote operation is canceled. I. C. Notice TERMINAL EQUIPMENT NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. [. . . ] Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner's manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). [. . . ]