User manual UNIDEN DXI860

[. . . ] Contents Controls and Functions (Handset) . Front Cover Foldout Controls and Functions (Base) . Front Cover Foldout Important Safety Instructions . 12 Installing the Handset Battery Pack . [. . . ] To change the Digital Code, be sure the Handset is on the Base, then: 1. Press page/find on the Base Unit. The Handset beeps and The Handset battery the battery icon flashes icon flashes once every once every 3 seconds. Complete your call as quickly as possible. Return the Handset to the Base Unit for charging. Return the Handset to the Base Unit for charging. Note: Allow 15 to 20 hours without any interruption for the Handset to fully recharge. Battery Memory Effect Rechargeable batteries can develop a "memory" (reduced charge capacity) caused by repeated charge and discharge cycles. The battery life will seem to be shorter every time you use the unit. To Avoid this Memory Effect At least once a month, operate the unit until the "Battery Low" indicator appears. Avoid "topping off" the charge after using the phone for a short time. Also, do not charge the Rechargeable Battery for extended periods of time. After the Handset stops beeping, remove it from the Base Unit. 0 1 tal k ca lle r id m me 4 gh i 2ab c 7pq rs ton e * 5 jkl 6mn 3def 8tuv fla sh o 0op 9 wx fun cti on pa us redia e ca nc er vo lum e ch an de let e yz l # el Setting the Pulse/Tone Switch Be sure the PULSE/TONE switch is in the TONE position. 3. Wait 5 seconds then place the Handset on the Base Unit. Note: Most phone systems are Tone dialing. Check with your local phone company if you are not sure whether your system is Tone or Pulse dialing. 4. The Battery icon will blink to indicate that the Digital Security Code is set to one of the more than 65, 000 codes. 14 DXI860 If the Base Unit loses power while the Handset is off the Base, the Digital Code may be erased. When this happens, the Handset will not function. To reestablish communication between the Handset and Base Unit: 1. Place the Handset back on the Base Unit. The Battery icon will blink to indicate that the Digital Security Code is set. Handset Volume Controls Please refer to the foldout in front of your operating guide for key positions. To adjust the ringer volume of your Handset, press volume/cancel until you hear the desired ringer tone and volume. Ring T ype A High Two-tone High Ring T ype A Low Two-tone Low Ring T ype B High Three-tone High Ring T ype B Low Three-tone Low To adjust the receiver volume, press volume/cancel while you are on a call. VOLUME HIGH High VOLUME LOW High DXI860 15 Entering the Local Area Code Note: Please refer to the foldout in front of your operating guide for key positions. You must enter your local area code for the Caller ID redial features to work properly. The Battery icon will blink to indicate that the area code has been deleted. Setting Caller ID on Call Waiting Note: You must subscribe to Caller ID on Call Waiting from your local phone service to use this feature. You can set your DXI860 phone to display information about calls that generate a call waiting tone while you are on a call. Note: With this feature set you will not be able to hear the person you are talking to for a brief period after you receive the call waiting tone. To turn Caller ID on Call Waiting on: 1. Remove the Handset from the Base Unit. AREA CODE 1AREA CODE 1-817 STORING 6 CALLS 3. A confirmation tone sounds and the display remains on for two seconds. [. . . ] To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. Rechargeable Nickel-Cadmium Battery Warning H This equipment contains a Rechargeable Nickel-Cadmium Battery. H Cadmium is a chemical known to the State of California to cause cancer. H The Rechargeable Nickel-Cadmium Battery contained in this equipment may explode if disposed of in a fire. H Do not short-circuit the battery. [. . . ]