User manual UNIDEN UBC69XLT

[. . . ] UBC69XLT SCANNER 80 Channels with 3 band plan UB334 Paper OM reduced size. fm Page 2 Friday, September 9, 2005 11:16 AM Precautions Before you use this scanner, please read and observe the following. EARPHONE WARNING!An incorrect earphone may be hazardous to your hearing. Turn down volume before connecting the earphone and then adjust volume to suit. WARNING! Uniden does not represent this unit to be waterproof. To reduce the risk of fire or electrical shock, do not expose this unit to rain or moisture. [. . . ] Press and hold for about 2 seconds to turn the scanner on, then turn Volume clockwise until you hear a hissing sound. If the scanner is scanning, press Hold to stop scanning, then turn Squelch clockwise until the hissing stops. Storing Known Frequencies Into Channels 1. Then enter the channel number where you want to store a frequency, then press Func and Pgm. Use the number keys and /Clr to enter the frequency (including the decimal point) you want to store. Press E to store the frequency into the channel. Notes: · If you entered an invalid frequency in Step 2, Error appears and the scanner beeps three times. The scanner automatically rounds the entered number to the nearest valid frequency. (MHz), your scanner accepts it as 28. 475. When you enter a frequency into a channel, the scanner automatically turns on the delay function and DLY appears. When delay is turned on, the scanner automatically pauses scanning · · Operation 25 UB334 Paper OM reduced size. fm Page 26 Friday, September 9, 2005 11:16 AM 2 seconds after the end of a transmission before scanning proceeds to the next channel. To turn the function off or on, press Func + Dly. · If you enter a frequency that has already been entered elsewhere, the scanner sounds an error tone and displays the channel that was duplicated. If you entered the frequency by mistake, press Clr then enter the correct frequency. To enter the frequency anyway, press E to accept. 4. To program the next channel in sequence, press E/Pgm then repeat Steps 2 and 3. Searching For and Temporarily Storing Active Frequencies If you do not have a reference to frequencies in your area, use a search to find a transmission. Note: When the scanner starts searching, it automatically turns on the delay function. To turn delay on or off, press Func + Dly. Scanning the Stored Channels To begin scanning channels, press Scan. The scanner scans through all non-locked channels (See "Locking Out Channels" on Page 33). When the scanner finds a transmission, it stops on it. When the transmission ends, the scanner resumes scanning. Operation 26 UB334 Paper OM reduced size. fm Page 27 Friday, September 9, 2005 11:16 AM Notes: · · If you have not stored frequencies into any channels, the scanner does not scan. If the scanner picks up unwanted partial, or very weak transmissions, turn Squelch clockwise to decrease the scanner's sensitivity to these signals. To listen to a weak or distant station, turn Squelch counterclockwise. [. . . ] 80 Frequency Range (in MHz): Sensitivity (SINAD 12 dB) 25. 005 MHz (FM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 3 µV 54. 050 MHz (FM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 3 µV 86. 275 MHz (FM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 3 µV 138. 150 MHz (FM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]