User manual UNIDEN XCI660

[. . . ] 36 Using the Flash Key with Call Waiting . 41 Storing a Caller ID memory number in Dial Memory . 41 Storing a Regular Number in Dial Memory . 43 Editing and Deleting Numbers in Dial Memory . [. . . ] Push up on the Handset retainer on the Base Unit, and slide the tab out. 20 2. Flip the retainer over so the tab faces up. 3. Put the retainer back into its slot on the Base Unit. 4. Push down on the Handset retainer until it snaps into place. 21 Setting Up Your Phone Extending the Antenna Before using your phone, be sure to raise its antenna to the vertical position. Installing the Handset Battery Pack 1. Press in on the Battery Cover Release. 2. Slide the battery compartment cover down. 22 3. Align the plastic connector of the Nickel-Cadmium battery pack with its socket and plug it in. Note: The black lead will be on the left when the plug is properly aligned. 4. Place the battery pack inside the battery compartment, and slide the battery cover back on. h The built-in Memory Backup feature allows up to 3 minutes to disconnect the old battery pack and install a new one without losing any numbers stored in memory. 23 Cleaning the Battery Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset and Base Unit about once a month. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents. page/find Contacts Contacts 24 Charging the Battery Pack Initial Battery Charging The rechargeable Nickel-Cadmium battery pack must be fully charged before using your phone for the first time. We recommend that the battery pack charge for approximately 15-20 hours, without interruption, before plugging the phone line into your new phone. Either place the Handset facedown -- OR -- Hang the Handset on the cradle when the phone is mounted on a wall. Note: Make sure to change the Handset Retainer before hanging up the phone. 2. If the icon doesn't light, check to see that the AC adapter is plugged in, and that the Handset is making good contact with the Base Unit charging contacts. talk caller id mem tune flash redial volume chan function pause cancel delete TOTAL CALLS 10 25 Continuous Battery Charging For the best battery performance, return the Handset to the Base Unit at the end of the day. This keeps the battery fully charged, so your phone works best. Low Battery Indicator When the Battery Pack in the Handset is very low and needs to be charged, the Battery icon flashes. TOTAL CALLS 10 If the Battery icon begins to flash, the phone is programmed to eliminate its functions to save power. The table below describes what to do to return your phone to normal operation. During a Call In Standby Mode Only the TALK button operates. The Handset beeps and the Battery icon flashes once every 3 seconds. Complete your call as quickly as possible. Return the Handset to the Base Unit for charging. None of the buttons will operate. The Handset beeps and the Battery icon flashes once every 3 seconds. Return the Handset to the Base Unit for charging. h Allow 15 to 20 hours without any interruption for the Handset to fully recharge. 26 Setting the Pulse/Tone Switch Be sure the PULSE/TONE switch is in the TONE position. PULSE­TONE h Most phone systems are Tone dialing. Check with your local phone company if you are not sure whether your system is Tone or Pulse dialing. Adjusting Ringer Controls h Please refer to the foldout in front of your operating guide for key positions. To adjust the ringer volume of your Handset, press volume/cancel until you hear the desired ringer tone and volume. Ring T ype A High Two-tone High Ring T ype A Low Two-tone Low Ring T ype B High Three-tone High Ring T ype B Low Three-tone Low To adjust the receiver volume, press volume/cancel while you are on a call. VOLUME HIGH High VOLUME LOW High 27 Automatic Digital Code Security To avoid unauthorized calls on your phone, a Digital Code feature was added to the XCI-660 S eriesphone. This Digital Code is shared only between the Handset and Base Unit. [. . . ] This will prevent the battery from completely discharging. Hear only continuous static from Handset and phone will not turn off. 47 660CH3E. CHP Mon Nov 03 16:55:38 1997 Specifications General ­ The XCI-660 Series complies with FCC Parts 15 and 68. Frequency Control Modulation Operating Temperature Base Unit Receive Frequency Transmit Frequency Power Requirements Size (w/o antenna) Weight Handset Receive Frequency Transmit Frequency Power Requirements Size Weight (w/battery) Battery 43. 72 to 46. 97 MHz (25 Channels) 48. 76 to 49. 99 MHz (25 Channels) Rechargeable Ni-Cd Battery Pack 7¾"H X 2"W X 2¼"D Approximately 11. 7 oz. BT-185 Capacity Talk Mode Standby Mode 270mAh 3. 6V 8 hours 14 days 48. 76 to 49. 99 MHz (25 Channels) 43. 72 to 46. 97 MHz (25 Channels) 120V AC 60 Hz 3V AC 8. ½"H X 3. ½"W X 2. ¼"D Approximately 11. 1 oz. PLL FM -10°C to 50°C Specifications, Features, and availability of Optional Accessories are all subject to change without prior notice. 48 Color profile: Disabled Composite Default screen XC660CE. CHP Mon Nov 03 16:40:43 1997 PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. [. . . ]